Third-Party Parallel Printer Interfaces, 1980–1986
- Year
- 1980
- Type
- Interface
- Category
- Centronics printer interfaces and print spoolers
- Manufacturer
- Various (Macrotronics, Newell Industries, Protronics, Advanced Interface Devices, Axiom, Telesys, PS Technologies and others)
Why there were so many
The Atari 400 and 800 have no printer port of their own. Atari's printers plug into the SIO bus, but the popular Epson, Gemini, C. Itoh and NEC dot-matrix printers used a Centronics parallel input. Atari's answer was the 850 Interface Module, about $200 and often hard to find, with a printer port alongside four serial ports. Dozens of companies sold cheaper ways around it. They used three different routes into the computer, and the route decided how compatible each one was.
| Route | How it works | Catch |
|---|---|---|
| Joystick ports | Two controller jacks give eight data lines plus handshake lines | Needs its own P: handler, loaded from disk or tape or put in a replacement OS ROM. Software that bypasses the OS, or that uses the ports for joysticks, may clash |
| SIO bus | A small box answers to the computer as an 850-style printer device | Works with ordinary software. Units powered from SIO can be fussy on the 1200XL, which supplies no +5 V on the SIO port |
| Parallel bus (PBI) | A card on the 600XL/800XL expansion connector, using the XL OS's device handlers | XL only. Usually part of a bigger multi-function board |
Most of the major brands have their own entries: Digital Devices' Ape-Face and U-Print, Microbits/Supra's MPP-1100, MPP-1150 and MicroPrint, ICD's P:R: Connection and Printer Connection, Xetec's Graphix AT, ICECo's ICEPIC and Atari's own XEP80. This page covers the rest.
Joystick-port interfaces
- Macrotronics A4P / A8P (1980). One of the earliest add-ons for any Atari. It plugs into controller jacks 3 and 4 (A4P for the 400, A8P for the 800). One of four ribbon cables matched the printer: a 20-pin header for Trendcom 100/200, a 40-pin edge for the Atari 825 and Centronics 730/737/739, a 36-pin Centronics plug, or a DB-25 for IDS Paper Tiger models. A replacement P: handler, Parallel Print, came on cassette and disk. The A4PG/A8PG packages added Screen Print graphics-dump software for Centronics 739, Trendcom 200, IDS 440G/445G and Epson MX-70/80/100 (with Graftrax), and later Okidata and NEC 8023A. In August 1982 Antic found the cable-and-software combination capable but "overpriced". The same issue's printer-buffer test used the Macrotronics graphics interface to dump a full graphics screen to a buffered Epson in 31 seconds.
- Protronics R/128 (1983). A $399.95 "RAMdisk printer buffer spooler" with 128K of battery-backed RAM. It plugged into the joystick ports and was sold as a replacement for the 850 for printing. Protronics quoted 8K per second transfers and promised a 512K upgrade (Antic, November 1983).
- PS Technologies PST-8B (1985–86). Only $39.95 in Antic's January 1986 New Products. It connects to a controller jack, so the package included a replacement P: handler on disk and a new OS ROM. XL owners got a replacement ROM with a built-in translator, and 400/800 owners got a revision B OS chip.
- Others: Computer Support's Portprint (any XL/XE, replacement handler), W.E. Electronics' Printerface (one joystick port, driver on cassette), Laskys' Joy Print (two ports, driver on cassette), Super Products' SuperFace (port 2 on an XL/XE or port 4 on an 800, shipped with the PrintMon OS) and the ROM-Wizard interface, whose handler lives in the ROM-Wizard replacement OS.
In March 1984 Antic described a Japanese user group whose member had built his own Epson interface through the joystick ports. He also wrote a bootstrap that swapped Japanese kana into the character set.
SIO interfaces
- Newell Industries NI858-32 (1983). Newell's $229.95 alternative to the 850 offered RS-232 I/O and two parallel printer ports, one of them bidirectional. It had an 8K spooling buffer, expandable to 32K, serving both the serial and parallel sides, and could copy serial input straight to the printer.
- Advanced Interface Devices Interfast-I (1983). Uses the same DA-15 connector as the 850's printer port. It's programmable and can translate ATASCII, or any other character set, into printer graphics.
- Axiom ParallAx-AT (AT-486, 1984). $99 in Antic's September 1984 New Products. It acts like an 850 without the serial ports and has a pass-through SIO socket. Axiom also made the AT-100 printer, with an Atari cable built in.
- Telesys TurboPrint/A and TurboPrint/GTA. Their TurboText page formatting (margins, page numbering) works whatever the software does. The /A has an explicit listing mode that prints graphics and control characters as one- to three-letter codes in brackets. The /GTA can print Atari graphics characters, and plug-in TurboBuffer modules added 16K (B16) or 32K (B32).
- Other SIO cables: Cardco's CARD?/AT, the Blackthorn interface (with daisy-chain port), the FCC Systems interface, Wiesemann's 72000 (later Wiesemann & Theis), Germany's Compy-Shop Centronics-Druckerinterface and Klaus Peters' Centronics Interface II.
Built into other devices
Some drives and multi-function boards included a printer port. Examples are the Trak AT-D2/D4 drives with a 4K buffer, the ATR8000, the Micro MainFrame MF-1682, the Microperipheral AutoPrint Microconnection modem, CSS Black Box, ICD MIO, the Supra hard disk interface, the K-Products KPI and the Rambit Parallel Printer Port (PBI), and the 1050 upgrades 1050 Turbo and Mega Speedy.
Using one today
- Handlers matter. SIO interfaces behave like a printer on an 850 and work with almost all software. Joystick-port interfaces only work with programs that print through the OS's P: device after the special handler has been loaded. Many cartridges and games don't.
- Mind the 1200XL. SIO-powered interfaces may need a modification or an external-power version on the 1200XL. Interfaces powered from the printer need a printer that supplies +5 V on pin 18.
- Check the cable end. Interfaces with a DA-15 socket need an 850-style printer cable. Those with a fitted 36-pin Centronics plug connect directly. For home-made cables see DIY printer cables.
Credits
- comp.sys.atari.8bit FAQ (Michael Current), 4.6 How can I use a Centronics or IBM parallel interface printer? — Michael Current (comp.sys.atari.8bit FAQ)
- AtariMania FAQ mirror, 4.6 Centronics printers — AtariMania
- Antic Vol. 2 No. 8 (November 1983), New Products: NI858-32 (Newell), R/128 (Protronics) — AtariMagazines.com (Kevin Savetz), 1983
- Antic Vol. 3 No. 5 (September 1984), New Products: ParallAx-AT — AtariMagazines.com (Kevin Savetz), 1984
- Antic Vol. 4 No. 9 (January 1986), New Products: PST-8B Interface — AtariMagazines.com (Kevin Savetz), 1986
- Antic Vol. 1 No. 3 (August 1982), printer review and printer buffer article (Macrotronics) — AtariMagazines.com (Kevin Savetz), 1982
- Antic Vol. 2 No. 12 (March 1984), Atari Around the World (Japanese home-brew interface) — AtariMagazines.com (Kevin Savetz), 1984
- Gury's Atari 8-bit Forever portal — Interfast-I (Advanced Interface Devices, 1983) — Gury (Atari 8-bit Forever portal), 1983
- David A. Paterson, Atari 8-bit Hardware Upgrade FAQ (1996), N1858-32 and R/128 entries — David A. Paterson, 1996
