Microbits MPP-1100, MPP-1150 and Microprint Printer Interfaces
- Year
- 1983
- Type
- Interface
- Category
- Parallel printer interfaces and print buffer
- Manufacturer
- Microbits Peripheral Products (Albany, Oregon); later Supra Corporation
- Tags
- printer-interface, centronics, microbits, mpp, supra, joystick-port, sio, print-buffer
Overview
Microbits Peripheral Products (MPP), the Oregon company that later became Supra, built a small range of printer interfaces for owners who didn't want to spend about $200 on an Atari 850. The first, the MPP-1100, took an unusual route. It drove a Centronics printer from joystick port 3 and replaced one of the 400/800's OS ROM chips with an MPP version containing a new printer handler. The later MPP-1150 and Microprint connected over the SIO bus like an ordinary Atari peripheral. MPP also sold the Microstuffer, a 64K stand-alone print buffer.
Models
| Model | Connection | Notes |
|---|---|---|
| MPP-1100 | Controller jack 3; NTSC 400/800 only | Replacement OS ROM (for chip C012499) with new P: handler; Rev. B upgrade ROM needed on Rev. A machines; 36-contact Centronics plug; MPP-1102 adapter for 40-pin edge (Atari 825, Centronics 737) |
| MPP-1150 | SIO, with pass-through port | Powered from SIO, so not for the 1200XL; later built by Supra |
| MPP-1151 | SIO, with pass-through port | 1200XL version with its own power supply |
| Microprint | SIO cable to Centronics plug | Later built by Supra |
| Microstuffer | Between computer interface and printer | 64K buffer, Clear and Repeat buttons, self-test; optional RS-232 |
MPP-1100 in use
Antic reviewed the MPP-1100 in November 1983 at $99.95 including cable. The reviewer explained the installation: check your OS revision with ? PEEK(58383) (0 means Revision B), then swap the chips on the 800's OS card, or on the 400's main board, which is harder to reach. It took about 15 minutes with two screwdrivers. On his 800 with a Gemini 10 printer it "performed flawlessly during several months of heavy use" and worked with all his software, since it supports any program that prints through the OS handler "in a legal manner". MPP itself acknowledged two incompatible programs: Eastern House's Monkey Wrench II and early releases of Datasoft's Zaxxon.
Antic reviewed the Microstuffer in July 1985 at $149.95 and was using one itself: "It holds a whopping big file in its memory."
Using one today
- The MPP-1100 depends on its replacement OS ROM and on the 400/800's four joystick ports. It doesn't work with XL/XE machines.
- The SIO models behave like any SIO printer interface. Use the MPP-1151 (or another powered interface) on a 1200XL.
- These interfaces send characters as-is. To print Atari graphics characters you need printer-specific software.
Credits
- Picture: The Microbits MPP-1150 parallel printer interface. — Photo from Gury's Atari 8-bit Forever portal (MPP-1150 Printer Interface) (Unknown, used for identification)
- Antic Vol. 2 No. 8 (November 1983), Product Reviews: MPP-1100 Parallel Printer Interface (F. Neil Simms) — AtariMagazines.com (Kevin Savetz), 1983
- Antic Vol. 4 No. 3 (July 1985), Product Reviews: Microstuffer — AtariMagazines.com (Kevin Savetz), 1985
- comp.sys.atari.8bit FAQ (Michael Current), section 4.6 (Microbits MPP-1100, MPP-1150, MPP-1151, MicroPrint) — Michael Current (comp.sys.atari.8bit FAQ)
- Gury's Atari 8-bit Forever portal: MPP-1150 Printer Interface — Photo from Gury's Atari 8-bit Forever portal (MPP-1150 Printer Interface) (Unknown, used for identification)
