Mega Speedy

Year
2014
Type
Modern device
Category
Modern multi-mode Atari 1050 drive upgrade
Manufacturer
Guus Assmann (hardware) and Matthias Reichl (firmware, logic); from an initial design by Wolfram Fischer
Red Mega Speedy circuit board with a 65C02, CPLD and flash chips, a buzzer and a ribbon cable to a small two-digit LED display and rotary knob

Overview

The Mega Speedy is a modern replacement controller for the Atari 1050 that can become most of the classic 1050 upgrades on demand. It took 2nd place in the ABBUC Hardware Contest 2014 with 582 points. Out of the box it runs as a stock 1050, a Speedy (with track display and buzzer), a Super Speedy (192 KB buffer and SuperCopy), a 1050 Turbo (with its speed switching and Centronics printer port), a 1050 Duplicator, and its own new Mega Speedy mode. If you own the original upgrades and supply their ROMs, it can also act as a Happy 1050, US Doubler, Super Archiver (including speed switching and fuzzy or weak-sector writing) and SuperMax.

Wolfram Fischer (mega-hz) started the project. He drew the first PCB and built a prototype that ran in original and Super Speedy modes before handing it to Guus Assmann, who designed the production hardware, and Matthias "Hias" Reichl, who wrote the firmware, flasher and CPLD logic. Jim Patchell let them use the 1050 Duplicator code. The schematics, CPLD sources, flasher and configuration ROM are published on Hias' website.

Specifications

Item Value
Design Guus Assmann, Matthias Reichl; initial design Wolfram Fischer
Year 2014 (2nd place, ABBUC Hardware Contest 2014)
CPU 65C02
Logic Xilinx CPLD
Flash 512 KB (drive ROMs, 4 slots per mode)
RAM 512 KB SRAM
Mega Speedy mode Speedy-compatible, 32 KB ROM and 448 KB RAM
Controls Two-digit LED display, rotary encoder with push button, up to two optional preset switches, reset button
Extras Speedy buzzer and track display; Centronics port in 1050 Turbo mode; built-in flasher and disk copier
Production Small run of 100 PCBs; about $50 plus shipping through ILS in the US

Modes and ROM slots

The display shows the mode letter and the ROM slot number:

Display Mode Factory ROMs
E Mega Speedy Speedy ROM V1.6 + flasher
S Super Speedy Speedy ROM V1.5 + Super Copy
y Speedy Speedy V1.4 with Bibo-DOS, HSS Copy or Floppy 2000 utilities
o Original 1050 1050 ROM revisions L, K and J
t 1050 Turbo 1050 Turbo ROM V3.5 and V3.4
d 1050 Duplicator Duplicator V3.00, and V3.10 with track buffer off
H / U / A / u Happy / US Doubler / Super Archiver / SuperMax Empty, so you flash your own ROMs
FL Flasher Boots the flasher from the drive

Each mode has four ROM slots, so you can keep different versions side by side, such as a Speedy with Bibo-DOS and a Speedy with a copier.

How it works

At power-up, or when you press its reset button, the board enters configuration mode. The display shows the current choice and the encoder lights up. Turn the knob to pick a mode and slot. After about three seconds of idle time the choice is activated, and pressing the knob both activates it and saves it as the default. With one or two optional toggle switches you can store up to four presets, such as "original 1050", "1050 Turbo" and "Speedy", and flip between them.

You can also configure it from the Atari. In flasher or Mega Speedy mode, booting with the drive door open loads a menu straight from the drive. From there you pick a mode (SHIFT+RETURN saves it as the default), start the flasher, or launch MyPicoDos. The flasher, also on the support disk as FLASH.COM, programs ROM images into flash, backs up the flash to a file, and can upload a drive ROM into RAM for testing. That makes the Mega Speedy handy for drive firmware development as well as everyday use.

The internal copy program can read an entire double-density disk into the board's SRAM and write it back out, so single-drive disk copying needs no swaps.

Using it today

  • Installation is internal to the 1050. Steve Carden of ILS wrote installation documents and beta-tested the design.
  • Pick the mode to suit the software. Speedy and Mega Speedy work with Speedy-aware DOSes and high-speed OS patches. The 1050 Turbo mode serves Turbodrive software. Duplicator mode adds UltraSpeed compatibility and copying tools. "Original 1050" is there for awkward protected disks.
  • Bring your own ROMs for Happy, US Doubler, Super Archiver and SuperMax. The team didn't have permission to distribute them, and you're expected to own the original upgrade.
  • Recovery. The flasher slot is meant to be left alone, so you can always get back into the menu even if you've corrupted the other slots.

Compatibility

The Mega Speedy is only for the Atari 1050. Because it reproduces each original upgrade's firmware behaviour, software written for those upgrades, such as Speedy copiers, Turbodrive DOSes, Duplicator copy programs and Archiver tools, should behave as it did on the real hardware. The supported formats are those of the selected mode: SD, ED and DD in all the double-density modes.

Credits