DIY Printer Cables for the Atari 850
- Year
- 1984
- Type
- DIY project
- Category
- Cable / printer switch
- Manufacturer
- Homebrew designs (Robert DeWitt; Hans Hsu), published in Antic
- Tags
- printer, centronics, 850-interface, cable, da-15, dpdt, antic, diy, beginner
Overview
The Atari 850 Interface Module gave the 400/800 a parallel printer port. It wasn't a standard Centronics socket, though, but a 15-pin D connector. Atari printers came with the right cable. Most third-party printers didn't, and ready-made cables cost extra. Antic published two simple cable projects that every 850 owner could use.
Project 1: a Centronics cable for the 850
"A Cable for Your Printer" by Robert DeWitt, Antic managing editor, ran in Vol. 2 No. 10 (January 1984).
You need:
- a DA-15P plug (male) for the 850. Not the DA-15S socket.
- a 57-20360 36-pin Centronics plug for the printer. Avoid the similar ICN-365: it's easier to fit but doesn't let you route the wires in the order needed.
- 5–6 feet of multicoloured ribbon cable with at least 12 individually insulated wires. Clip unused wires back so they can't short anything.
850 (DA-15P) pin usage:
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | Data Strobe | 9, 10 | not used |
| 2–8 | Data bits 0–6 | 11 | Signal ground |
| 15 | Data bit 7 | 12 | Fault |
| 13 | Busy | ||
| 14 | not used |
Wiring to the 36-pin Centronics plug:
| Centronics pin | Connect to 850 signal |
|---|---|
| 1 | Data Strobe |
| 2–9 | Data bits 0–7 |
| 11 | Busy |
| 16 | Signal ground |
| 32 | Fault |
| all others | not connected |
Some printer manuals number data bits 1–8 instead of 0–7. Antic used this cable successfully with the Epson FX-100, Gemini 10X, Mannesmann Tally Spirit, NEC PC-8023A, Smith Corona TP1 and Transtar 120. For any other printer, check its pin-assignment table, because a few differ.
Project 2: the two-headed printer cable
In Vol. 4 No. 10 (February 1986), Hans Hsu, then just finished a Cambridge MA in Computer Science and the designer of JaneCalc for Arktronics, described "Create a Two-Headed Printer Cable". He had a daisy-wheel and a dot-matrix printer but only one 850 port, and was tired of swapping cables.
The idea: a parallel port has many lines, but only two control lines matter here. STROBE tells the printer the data lines are valid. BUSY tells the computer whether the printer can accept data. Wire all the data lines to both printers, but route STROBE and BUSY through a DPDT switch so only the selected printer sees them. Both printers receive the data, but only the one getting STROBE prints it.
Building it:
- Cut two existing printer cables in half, keeping both Centronics ends and one 850 (D-15) end.
- Solder the data lines of the three cable pieces together.
- Wire STROBE and BUSY from the 850 end to the DPDT switch's common terminals, and each printer's STROBE and BUSY to one side of the switch.
- Mount the switch on a 1.5" × 0.5" piece of perfboard, slide it into a slit cut in a 35 mm film canister, and poke the toggle through a hole in the lid.
- Test: with both printers online, print something, see which one responds, and label the switch positions.
Centronics pinouts vary between printers, so check your manuals before soldering.
Tips
- A homemade DA-15 to Centronics cable is the cheapest way to connect an 850 to a standard parallel printer.
- The 850 pin table above also tells you which signals to probe when an 850's printer port misbehaves.
- Some interfaces deliver only 7 data bits. The 850 port carries all eight, and pin 15 is data bit 7, so graphics printing works if bit 7 is wired.
Credits
- Picture: Hans Hsu's two-headed printer cable: the DPDT switch housed in a 35 mm film canister (Antic, Feb 1986). — Figure 2 from 'Create a Two-Headed Printer Cable' by Hans Hsu, Antic Vol. 4 No. 10 (Feb 1986), via atarimagazines.com (used for identification/commentary)
- Robert DeWitt — A Cable for Your Printer: The Centronics connection, Antic v2n10 (January 1984) — Robert DeWitt; AtariMagazines.com (Kevin Savetz), 1984
- Hans Hsu — Create a Two-Headed Printer Cable, Antic v4n10 (February 1986) — Figure 2 from 'Create a Two-Headed Printer Cable' by Hans Hsu, Antic Vol. 4 No. 10 (Feb 1986), via atarimagazines.com (used for identification/commentary), 1986
