Trak AT-D1, AT-D2 and AT-D4 Disk Drives
- Year
- 1983
- Type
- Storage
- Category
- 5.25-inch floppy disk drives (third-party)
- Manufacturer
- Trak Microcomputer Corporation (Downers Grove, Illinois)
Overview
Trak Microcomputer Corporation sold some of the most self-contained disk drives of the Atari's early years. Antic's August 1983 New Products column described the AT-D1 and AT-D2 as "intelligent drive systems" with an on-board microprocessor and programmed memory, in a case only 3 inches high. Two features set them apart from every other drive. A Centronics printer port was built in, so a standard parallel printer plugged straight into the drive with no Atari 850 or separate interface. And a digital track counter on the front showed where the head was. Later models added faster, track-buffered firmware ("Turbo Pak") and a double-sided version.
Models
| Model | Format | Printer buffer | Notes |
|---|---|---|---|
| AT-1 | SS SD/DD | Optional parallel interface (2 KB) | Plain drive without built-in printer port; Turbo Pak option |
| AT-D1 | SS SD (DD upgrade available) | 2 KB, upgradable to 16 KB | Launched 1983 at $469 |
| AT-D2 | SS SD/DD | 2 KB, upgradable to 16 KB | Launched 1983 at $499 |
| AT-D4 | DS SD/DD | 4 KB RAM, upgradable to 16 KB | "Turbo Software" reads 18 sectors at a time into RAM |
| AT-S1 / AT-S2 | SS or DS slave drives | n/a | Up to three slaves on a master's 34-pin header |
| Common item | Value |
|---|---|
| Interface | Atari SIO in/out (daisy-chain) |
| Printer port | 34-pin PCB edge connector (AT-D1, D2, D4), 850-compatible P: device |
| Turbo Pak ROM | Adds 2 KB (4 KB total) plus track-buffered reads |
| Bundled software | Trak Automatic Density Select (TADS) for Atari DOS 2.0S, utilities and games; later AT-D2 and AT-D4 units also DOS XL |
Antic gave Trak's address as 1511 Ogden Ave., Downers Grove, Illinois.
How it works
On the double-sided AT-D4 each side appears as a separate logical drive, D1: and D2:. The second side's sectors run in reverse track order, inner to outer. That's unlike the Percom and XF551 double-sided layouts, so AT-D4 back sides are a Trak-only format.
TADS (Trak Automatic Density Select) patches Atari DOS 2.0S so the drive switches between single and double density by itself. The printer port works as a normal P: device from the computer's point of view, with the drive's buffer RAM holding print data so the computer is freed sooner.
History and reception
Trak drives were sold in the same 1983-84 window as Percom, Rana and Astra drives. Antic's mid-1985 DOS survey counted Trak among the brands whose owners already had true double density, back when Atari's own drives didn't. The built-in printer port made a Trak drive plus a parallel printer a complete system for word processing without an 850 interface module.
Using one today
- Single-sided double-density Trak disks are standard 180 KB, 256-byte-sector disks. AT-D4 back sides need the original drive to read.
- The built-in parallel port is worth testing: with a Centronics cable it still drives period printers directly.
- Several upgrades (double density for the AT-D1, larger buffers, the Turbo Pak ROM) were sold separately, so drives in the wild vary. Check the ROM and RAM fitted before deciding which software to use.
Credits
- Picture: A Trak AT-D2, showing the digital track counter. — Photo from Gury's Atari 8-bit Forever portal (TRAK AT-D2) (Unknown, used for identification)
- comp.sys.atari.8bit FAQ (Michael Current), sections 3.2.5 and 4.6 — Michael Current (comp.sys.atari.8bit FAQ)
- Antic Vol. 2 No. 5 (August 1983), New Products: AT-D1 and AT-D2 — AtariMagazines.com (Kevin Savetz), 1983
- Antic Vol. 4 No. 3 (July 1985), Everything You Wanted to Know About Every D.O.S. — AtariMagazines.com (Kevin Savetz), 1985
