1050 Turbo (Bernhard Engl)

Year
1986
Type
Upgrade
Category
Disk drive upgrade module (Atari 1050)
Manufacturer
Bernhard Engl for Gerald Engl Computertechnik (Munich)
Atari 1050 disk drive

Overview

Bernhard Engl's 1050 TURBO module came out of a familiar complaint. In his 1986 foreword, written in Munich, he argued that the 1050's "catastrophic" ROM firmware ruined otherwise good hardware: no true double density, a painfully slow serial bus, a slow head-step rate, no Percom block support, and drives that were better than the 1050 sold only in the USA. His answer was a single module that replaces a ROM chip in the 1050 and plugs in without soldering. It adds true Percom-style double density, a 70,000-baud "TURBODRIVE" transfer mode, and an optional Centronics printer port, aimed at a "pocket-money" price.

Its high-speed protocol, usually called "Turbodrive" or "1050 Turbo", became a standard in its own right in German-speaking and Polish circles. It's supported by Ataserw's Top Drive 1050, the TOMS drives, Tygrys 2.0 and QMEG+OS.

Specifications

Item Value
Developer Bernhard Engl, for Gerald Engl Computertechnik; released 1986
Hardware Replacement ROM module (no extra CPU, no RAM buffer)
Drive CPU Stock 6507, 1 MHz
Firmware 8 KB
Formats SD, ED, true DD 180 KB (Percom-compatible)
High speed TURBODRIVE: 68,200 bit/s, advertised as "70000 baud"
Printer port Optional Centronics interface via a 36-pin edge connector; the printer cable cost 49 DM
Built-in software Backup Machine II, Magic Formatter, Maintenance Box

How it works

Engl's manual explains his design choice. Rival "American" speeders used RAM track buffers and needed a specially modified DOS. TURBODRIVE uses neither. Its installation menu loads from the module when you boot with the drive lever open. It then hooks the OS's serial routines, survives SYSTEM RESET "as if it belonged to the operating-system ROM", and works with any DOS. Speed comes from carefully optimised sector layouts instead of a buffer. Engl claimed a 300% speed-up overall, and argued that a buffer risks writing a stale track onto a newly inserted disk.

The trade-off is that disks must be reformatted in a TURBO layout to get full speed. The manual's first step is to create a "TURBO master disk": boot DOS through the menu, turn off write-verify (POKE 1913,80 for DOS II users), then format and write DOS. A shorter beep while DOS loads shows the bus is already running at 70,000 baud.

Double density joins what the manual calls the "exclusive Percom club". Disks interchange with Astra, Indus, Rana, Trak, NCT and Percom drives, and a supplied BASIC program patches Atari DOS II to switch densities automatically.

Installing and using it

  • Installation is fully plug-in. The kit includes the module, a speed-switch lead with a micro-hook clip, and the printer cable if ordered. Most drives also need four capacitors removed for TURBODRIVE to work. 1983 drives with an EPROM in that socket need a special module version.
  • The built-in Maintenance Box measures spindle speed. Engl specifies 288 RPM (286-291 allowed) for normal use, and a second speed of just under 270 RPM, set with a trimmer on the micro-hook lead, for the Backup Machine.
  • The firmware doesn't detect density if the drive is powered up with a disk already in it. Altirra's emulation includes a workaround, but on real hardware insert disks after power-on.

Clones and reproductions

Clones and reproductions include Ataserw's Top Drive 1050 (Poland, 1987/88, ROM by P.Z. Karen, with TURBO DOS), 1050 Turbo II (ABBUC, 2004, a "100% clone"), Jürgen van Radecke's Turbo 1050 Replica (2017), and the Mega Speedy, which includes a 1050 Turbo mode.

Credits