Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21)
- Year
- 1983
- Type
- Component
- Category
- Service documentation: 1025 mechanism, 8051 controller, self-test, adjustments and fault-finding
- Manufacturer
- Atari, Inc.; Howard W. Sams & Co.
- Tags
- 1025, printer, dot-matrix, service, repair, field-service-manual, sams, computerfacts, self-test, adjustments, 8051
- Related
- Atari 800XL Troubleshooting (Sams Computerfacts CC11), Atari 1020 and 1027 Printer Field Service Manuals, Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13), Atari 130XE Troubleshooting (Sams Computerfacts CC16), Atari 800 Troubleshooting (Sams Computerfacts CC7), Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual)
Overview
The Atari 1025 was Atari's 80-column dot-matrix printer for the XL era. Two service documents describe it. Atari's 1025 Printer Field Service Manual (copyright 1983) was written for authorised service centres. It has eight sections: theory, schematic, maintenance and testing, disassembly and adjustment, a diagnostic flowchart, a symptom checklist, parts lists, and a pocket for service bulletins. Howard W. Sams & Co.'s Computerfacts CP21, dated August 1986, covers the same printer for independent repairers. It has photos, waveforms taken with the printer in self-test mode, and a short list of checks for each fault. The two agree on all the mechanical settings, so either will do for a rebuild.
How the 1025 works, according to Atari
Atari calls the 1025 a desktop, receive-only, unidirectional serial impact dot-matrix printer. It plugs into the computer or a disk drive through either of two identical SIO sockets.
- Print head. Seven wires, each held back by a permanent magnet. Energising a coil cancels the magnet's pull, and a spring fires the wire at the platen. The head unplugs from the carriage and lifts out when a lock lever is pressed.
- Carriage. A pulse motor and toothed belt move the carriage. Four steps (30°) move it 1/10 inch. On a carriage return the motor runs backwards until a plate on the carriage interrupts an LED/photodiode home sensor. The same motor drives the ribbon: an eyelet lever reverses the feed direction when the ribbon's eyelet reaches it.
- Paper. A second pulse motor turns a pin-feed platen through reduction gears. 24 steps (180°) feed 1/6 inch. A microswitch actuator drops into a groove in the paper separator when the paper runs out.
- Electronics. One board holds an 8051 microcontroller clocked at 7.37 MHz, an 8155 RAM/I/O chip that also drives the motors, and a 2732 EPROM holding the character shapes. The transformer supplies 26 V AC, which is rectified for the motors and head, and 10 V AC, which feeds a 7805 regulator for the logic.
The printer accepts nine command codes: 5, 10 or 16.7 characters per inch, 6 or 8 lines per inch, 64 or 80 columns, and European characters on or off. At power-on it defaults to 10 cpi, 6 lpi, 80 columns and no European characters.
Testing
Atari's diagnostic program is a short BASIC listing that asks for a command code, then prints the character set in each pitch and line spacing. The technician measures the printout with a ruler. Light print on one side of the page means the platen-to-head gap needs adjusting. A misplaced first character means the home position needs setting.
The ROM self-test needs no computer. With the printer off and the top cover removed, move the shorting plug SP1, on the left corner of the board, from position A to position B with needle-nose pliers. Then load paper and switch on. The test prints only the defaults (10 cpi, 6 lpi, standard characters, 80 columns), so a fault in the other modes needs the BASIC program. Sams took all its waveforms with the printer running this self-test.
When the flowchart says to "swap out" chips, Atari means one at a time with known-good parts. Each suspect chip is then put back to confirm it really is faulty. If a single command code fails, Atari's advice is to swap the 8051 (Q8) and the chips at Q5 and Q6.
Fault-finding (Sams CP21)
- Dead. Check fuse F2 (both fuses are 1.75 A fast-blow), then diodes D5/D6 and the transformer. Look for 26 V at D26/D46 and 5 V at regulator Q1. If F1 has blown, check D1/D2 and the regulator, then look for 10.5 V at Q1 pin 1.
- Carriage won't move. Push the carriage right with the power off. At switch-on it should return home. If not, look for 26 V on CN4 pins 5 and 6, then 7.37 MHz at CPU pins 18 and 19, then measure the motor windings.
- No printing or missing dots. Clean the head face, check CN3 and the flat cable for pinched leads, then measure the head's coil resistances before replacing anything.
- No line feed. Check CN5, the feed motor's windings and the 26 V supply. If feeding is erratic, look for broken teeth in the left-hand gear train.
- Won't print from the computer. Check whichever SIO socket (CN6 or CN7) is in use, then the cable, then the board.
Adjustments
| Adjustment | Setting |
|---|---|
| Platen to print head | 0.45–0.5 mm gap, set by moving the carriage shaft at the snap-lever screws |
| Platen to paper separator | About 0.5 mm |
| Space belt tension | 80–140 g when the belt is pressed 5 mm at the marked point (idler bracket) |
| First character position | Rotate the space motor so the head stops at the home sensor; if that fails, move the belt one or two teeth on the pulley |
Atari's maintenance schedule is a dry-cloth clean of the ribbon and paper paths every six months or 300 hours. It also warns never to print without paper and ribbon. To open the printer, pull off the platen knob and top cover, loosen the switch assembly's two screws and slide it back, remove two screws inside the front, then tip the upper cover back off its hooks. Two screws hold the board, and four screws in rubber caps hold the mechanism to the base.
Related
For Atari's other printers see the 1020 plotter, the 1027 letter-quality printer and the 1029. For cable projects that drive parallel printers instead, see DIY printer cables.
Credits
- Picture: Sams Computerfacts CP21 for the 1025 printer, dated August 1986. — Cover of Sams Computerfacts CP21 (Howard W. Sams & Co., 1986), scan from the Internet Archive item 'Sams_Computerfacts_Atari_Model_1025_Printer_1986_Howard_Sams' (Fair use (cover of a service publication))
- Internet Archive item Atari1025PrinterFieldServiceManual (OCR text) — Internet Archive
- Internet Archive item Sams_Computerfacts_Atari_Model_1025_Printer_1986_Howard_Sams (OCR text) — Cover of Sams Computerfacts CP21 (Howard W. Sams & Co., 1986), scan from the Internet Archive item 'Sams_Computerfacts_Atari_Model_1025_Printer_1986_Howard_Sams' (Fair use (cover of a service publication))
