Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual)
- Year
- 1984
- Type
- Component
- Category
- Third-party service data: power checks, chip-level fault finding and board swapping for the 400
- Manufacturer
- Howard W. Sams & Co.; Sears (service documentation for the Atari 400)
- Tags
- atari-400, service, repair, troubleshooting, sams, computerfacts, sears, power-supply, test-cartridge, 400-800
- Related
- Atari 800 Troubleshooting (Sams Computerfacts CC7), Atari 130XE Troubleshooting (Sams Computerfacts CC16), Atari 800XL Troubleshooting (Sams Computerfacts CC11), Atari 810 Troubleshooting (Sams Computerfacts CD9), Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21), Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13)
Overview
The Atari 400 was serviced in two very different ways, and a surviving document covers each one. Sams Computerfacts CC5, printed by Howard W. Sams & Co. in August 1984, is a component-level folder for TV and radio shops. It has schematics, board photos, logic-probe charts, a parts list and a step-by-step troubleshooting guide that names the chip behind each symptom. The Sears repair manual for the 400 is a module-swap guide from the machine's early years. It tells a technician to find the bad board by substituting known-good spares, then prove the repair with a test cartridge. Together they show how a 400 was fixed in its own time, and both still help anyone reviving one today.
Sams CC5: the chip map
CC5 uses Atari's board reference numbers, so it lines up with the 400/800 field service manual and with Sams' own 800 folder (CC7).
| Ref. | Part | What the guide checks it for |
|---|---|---|
| A101 | POKEY | Keyboard scan (pins 16, 18–25, key pulse on 29), cassette data (24, 26–28), paddles, TV audio (pin 37) |
| A102 | PIA | Joysticks, paddle buttons, cassette motor (pin 39) |
| A103, A104 | OS ROMs | Machine won't start although power and clock are good |
| A105 | ROM | Cartridges don't work |
| A111 | Video/sync buffer | No video or no sync, though CTIA's outputs are good |
| A201, A202 | Regulators | 23.7 V/12.25 V and 11.84 V/5.08 V rails |
| A301 | CTIA | Sync (pin 25), colour (pins 17, 21, 28), keyboard click (pin 15), console keys (pins 12–14) |
| A302 | ANTIC | Display data, SYSTEM RESET line (pin 6) |
| A303 | 6502 CPU | Clock in at pin 37, address and data activity |
| Z101, Z102 | Keyboard decoders | Several keys dead |
| X101 | 3.58 MHz crystal | Machine dead with good power |
Sams CC5: working through a dead 400
The preliminary checks start with the obvious: the power LED (CR210), the channel switch (S201) set to the same channel as the TV, the TV/computer switch box and every cable. Then come the supply checks. Unplug P204 and look for 10.42 V AC from the power pack, then 11.84 V at the bridge rectifier, 5.08 V at regulator A202, 23.7 V and 12.25 V at A201, −11.85 V at diode CR202 and −5.01 V at zener CR201. Each missing voltage comes with its own list of diodes and capacitors to test, plus a warning to look for shorts to ground. Note that the cartridge-door interlock (S202) sits in the AC path, so an open door also gives a dead machine.
If the supply is good but nothing appears, the guide checks the crystal, swaps the CPU and 16K RAM boards, and then suspects the ROMs, the video buffer and the address decoders. Its other checks follow the 800 folder closely:
- CPU. Use a logic probe on data pins 26–33 and address pins 9–20 and 22–25. Then check the clock at pin 37 back through clock transistors Q103/Q104 to CTIA pin 30.
- No colour. Look for the colour waveform at CTIA pin 21. As the colour control R309 is turned, the voltage at pin 17 should swing from about 7 V down to 0 V.
- Keyboard click. Run
10 PRINT CHR$(253): GOTO 10and look for 0.7 V peak-to-peak pulses at CTIA pin 15, then check audio transistor Q101 and the speaker. - TV sound. Run
10 SOUND 0,100,10,15: GOTO 10, check POKEY pin 37, then check that the Q105 sound oscillator runs at 4.5 MHz. - Keyboard. Check the scan waveforms on POKEY pins 18–23. Pin 16 is active for BREAK, CTRL and SHIFT, and pin 25 for the ordinary keys. Pin 29 should pulse on each keypress.
- Cassette. Watch POKEY pins 26–28 while saving and pin 24 while loading.
POKE 54018,52starts the recorder motor andPOKE 54018,60stops it, so PIA pin 39 and switch transistor Q102 can be checked. - Controllers. Short BASIC loops print
PADDLE(P)/PTRIG(P)andSTICK(P)/STRIG(P)for every port. A paddle should read from 228 down to 1 across its travel. A joystick reads 15 at rest, and a button 1 changes to 0 when pressed.
Three adjustments finish the job: set the sound coil L101 to 4.5 MHz with a pickup loop and frequency counter, tune RF coil L210 on channel 2 or 3 with the TV's AFC off, and turn R309 for a blue screen. To get inside, take out four screws underneath, open the cartridge door, and lift off the top. The power board comes out once two screws and the door's on/off lever are removed. The shield is held by eight more screws.
The Sears manual: swap boards, then test
The Sears guide describes the 400 as delivered at first: 8K of RAM with a 16K RAM board as an option, a 9 V AC power adaptor, two 4K OS ROMs and a 2K floating-point ROM on the personality board, and a power-up "Atari Computer — Memo Pad" screen. Its theory section explains, among other things, how the RAM board multiplexes a 13-bit address through seven-line DRAMs, and how paddles (100K pots), joysticks and the gray-code driving controllers reach the console.
Its method is different from Sams'. A symptom table first decides whether the console, power adaptor, switch box, cartridge, tape or controller is at fault. A bad console is then fixed by replacing its boards one at a time with known-good spares, easiest first. The guide warns that reseating a board and its socketed chips often cures the fault. It also warns that heat-related faults vanish once a board cools, so suspect boards should be kept powered. Repairs end with a Stand Alone Test. This uses a test cartridge and jumper plugs for the controller and peripheral ports, and offers video, colour-bar and grey-bar tests (A, C, G), port (P), RAM (R), tone (T) and keyboard tests. The colour pot is reached through the top cover's vent fins with a small screwdriver while the colour bars are shown.
Using them today
The Sams voltage table is the quickest way to check a 400 power board, and its chip map tells you which socketed part to try next. The Sears board-swap approach suits anyone with a spare parts machine, and its advice to reseat boards and chips before replacing anything still holds. For later diagnostics see the SuperSALT kit. For the machine itself see Atari 400, and for supply details see Atari power supplies.
Credits
- Picture: Sams Computerfacts CC5 for the Atari 400, dated August 1984. — Cover of Sams Computerfacts CC5 (Howard W. Sams & Co., 1984), scan from the Internet Archive item 'SamsComputerfactsAtari400B' (Fair use (cover of a service publication))
- Internet Archive item SamsComputerfactsAtari400B (OCR text) — Cover of Sams Computerfacts CC5 (Howard W. Sams & Co., 1984), scan from the Internet Archive item 'SamsComputerfactsAtari400B' (Fair use (cover of a service publication))
- Sears Source 637 Computers: Atari 400 Repair Manual (Internet Archive, OCR text) — Internet Archive
