Atari 800XL Troubleshooting (Sams Computerfacts CC11)
- Year
- 1985
- Type
- Component
- Category
- Third-party service data: self-test, clock chain, video, keyboard and I/O fault-finding for the 800XL
- Manufacturer
- Howard W. Sams & Co. (service documentation for the Atari 800XL)
- Tags
- 800xl, service, repair, troubleshooting, sams, computerfacts, self-test, clock, ic-map, adjustments, xl-series
Overview
Computerfacts CC11 is Howard W. Sams & Co.'s service folder for the Atari 800XL, dated July 1985. Like Sams' folders for the 400, 800 and 130XE, it has full schematics, board photos with grid locations, logic-probe charts, waveforms and a parts list. Some of the parts are marked as used only in United Kingdom models. Its preliminary checks give a quick symptom-to-chip list, and its troubleshooting section then walks through each fault pin by pin. The 800XL is far simpler inside than the 800: one board, one 5 V supply and no plug-in modules. As a result, much of the folder is about chips and the clock chain rather than power rails.
Chip map (as used in the folder)
| Ref. | Part | Typical faults |
|---|---|---|
| U1 | Audio amplifier | No TV/monitor sound although POKEY pin 37 is active |
| U2, U3 | Address decoder, memory management unit | CPU starts and then stops |
| U4, U5 | BASIC and OS ROMs | Machine won't come up; ROM bar red in self-test |
| U7 | ANTIC | No video, wrong characters, no 1.79 MHz at pin 34 |
| U8 | 6502 CPU | Dead machine: address pins 9–20 and 22–25, data pins 26–33 |
| U9–U16 | 64K×1 DRAMs | Red squares in the memory test |
| U17 | GTIA | Sync (pin 25), colour (pins 17, 21, 28), key click (pin 15), console keys (pins 12–14), joystick buttons |
| U18, U19 | Clock and reset logic | No clock at U18 pin 11; reset at U19 pin 8 |
| U20 | Video/sync buffer | No video though GTIA is working |
| U22 | POKEY | Keyboard scan (pins 16, 18–23), cassette (24, 26–28), paddles, sound |
| U23 | PIA | Joystick directions, paddle buttons, cassette motor (pin 39) |
| U24, U25 | Keyboard multiplexers | Dead groups of keys; SHIFT/CTRL/BREAK |
| U29 | Delay line | Pulses missing at pins 4, 6, 8, 10 or 12 |
| Y1 | 3.579545 MHz crystal | Oscillator transistors Q8/Q9 |
Start with the self-test
CC11 tells the technician to use the 800XL's own self-test first. Hold OPTION at power-on, or type BYE in BASIC. In the memory test, two bars stand for the OS ROM and 48 squares for 1K blocks of RAM chips U9–U16. Each turns green if good and red if bad. The audio-visual test plays a six-note tune on POKEY's four voices. A note on screen with no sound points to POKEY (U22). A sound with no note points to ANTIC (U7) or GTIA (U17). The keyboard test shows each key in inverse video as it is pressed, except RESET, HELP and BREAK.
The fault-finding sequence
- Dead computer. Unplug the power pack and look for 5.0 V between pins 3 and 1 of its plug (P7). If the pack is bad, first check for a short across the computer's power jack (J7) with the switch on, and don't plug in a new pack until any short is fixed. With a good pack, check for 5.0 V at electrolytic C2, and suspect the power switch S1 if it's missing.
- CPU not running. Reset (U19 pin 8) should go low briefly and then stay high. There should be a 1.78977 MHz clock at U18 pin 11. If an address or data pin seems stuck, remove the CPU and check again with it out. If pulses start at power-on and then stop, check the decoder (U2), the MMU (U3) and the ROMs.
- Clock chain. Look for 3.579545 MHz at oscillator transistor Q8, then follow the signal to GTIA pin 29, ANTIC pin 34 (1.79 MHz), U18, CPU pins 3 and 39, U19, and finally the delay line U29.
- Video, colour and sync. Trace the video from the RF modulator back through video amp Q3 and buffer U20 to GTIA and ANTIC. As colour control R38 is turned, GTIA pin 17 should swing from 0 to about 8.5 V. Check the colour waveform at pin 21 and the 3.579545 MHz at pin 28. Sync comes from GTIA pin 25 through U20.
- Sound. Run
10 SOUND 0,100,10,15: GOTO 10. Check POKEY pin 37, then U1 pin 1, then the RF modulator's sound coil L202. A missing keyboard click is traced to GTIA pin 15. - Keyboard. Check the scan on POKEY pins 18–23 and the return at U24 pin 3. SHIFT, CTRL and BREAK go through U25 pin 5 to POKEY pin 16. START, SELECT and OPTION pull GTIA pins 12, 13 and 14 low. The folder gives a table of which connector J8 pin carries each group of keys. Each key should measure about 55 ohms when pressed, and a single erratic key just needs cleaning.
- Cassette and controllers. The POKEY and PIA checks match the earlier folders, with the same
POKE 54018,52/60motor test and BASIC loops forPADDLE/PTRIGandSTICK/STRIG. A paddle should read from 228 down to 1. GTIA handles joystick buttons and the PIA handles stick directions.
Adjustments and disassembly
Set colour control R38 for a blue screen. With the TV on channel 2 or 3 and AFC off, adjust channel coil L201 for the best picture. While the SOUND loop runs, adjust sound coil L202 for most sound with least noise. To open the case, take out six screws underneath and lift the top, unplugging the keyboard cable. Four screws hold the board, and ten more hold the two halves of the shield together.
Related
The Electronic Dimensions 800XL manual covers the same board with a different symptom chart and SuperSALT test references. The machine itself is described in Atari 800XL.
Credits
- Picture: Sams Computerfacts CC11 for the 800XL, dated July 1985. — Cover of Sams Computerfacts CC11 (Howard W. Sams & Co., 1985), scan from the Internet Archive item 'atari800xlsamscomputerfactstechnicalservice' (Fair use (cover of a service publication))
- Internet Archive item atari800xlsamscomputerfactstechnicalservice (OCR text) — Cover of Sams Computerfacts CC11 (Howard W. Sams & Co., 1985), scan from the Internet Archive item 'atari800xlsamscomputerfactstechnicalservice' (Fair use (cover of a service publication))
