Atari 130XE Troubleshooting (Sams Computerfacts CC16)
- Year
- 1986
- Type
- Component
- Category
- Third-party service data: chip map and fault-finding for the 130XE
- Manufacturer
- Howard W. Sams & Co. (service documentation for the Atari 130XE)
- Tags
- 130xe, service, repair, troubleshooting, sams, computerfacts, schematics, self-test, ic-map, xe-series
- Related
- Atari 800XL Troubleshooting (Sams Computerfacts CC11), Atari 800 Troubleshooting (Sams Computerfacts CC7), Atari 130XE, XL/XE Self Test, Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21), Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual)
Overview
Howard W. Sams & Co. published Computerfacts, independent service manuals for popular home computers, in the same style as its long-running "Photofacts" for TVs and radios. Each one has complete schematics, annotated board photos, waveforms, parts lists, a semiconductor cross-reference, "preliminary service checks" and troubleshooting tips. Atari titles in the local collection cover the 400, 800, 800XL, 130XE, 810, 1050 and 1025. The 130XE folder is CC16, published in 1986. Since Atari's own XE field service documentation is hard to find, CC16 is one of the most practical repair references for the machine. This page summarises its troubleshooting section.
Chip map used in the fault guide
| Ref. | Part | Role in fault-finding |
|---|---|---|
| U2, U3 | Address decoder and memory management unit | Suspects when CPU address/data activity starts and then stops |
| U4, U5 | OS ROM and BASIC ROM | Self Test flags the OS ROM (U5) |
| U6 | Clock section | The guide checks the 14.31818 MHz oscillator (Y1) and the derived 3.579545 MHz and 1.78977 MHz signals at this chip |
| U7 | ANTIC | In the audio-visual test, a tone with no note on screen means a video fault in ANTIC or GTIA |
| U8 | CPU (6502C) | Check address pins 9–20 and 22–25 and data pins 26–33 |
| U9–U16 | RAM chips | The Self Test memory test shows 48 squares, each representing 1K of the RAM ICs (U9–U16), plus bars for the ROMs: white = being tested, green = good, red = bad |
| U17 | GTIA | Colour, sync and the console keys; shares the blame with ANTIC for video faults |
| U19 | Reset IC | Pin 3 should go low briefly at power-on or RESET, then high |
| U20 | Video buffer | Check if there's no picture |
| U22 | POKEY | Audio (a note shown with no sound points here), keyboard scan, paddles, cassette data |
| U23 | PIA | Joystick ports; also check the 1.78977 MHz clock at its pin 25 |
| U24, U25 | Keyboard multiplexers | Check pin 3 pulses while pressing keys |
Typical checks
- Power. Unplug the power pack and check 5.0 V between pins 3 and 1 of its plug. If the unit is dead with a good pack, check for 5 V on electrolytic C2 and the power switch S1.
- No CPU activity. Check the reset circuit (U19, C200, R39, R40), then the clocks, then the CPU's address and data pins for pulses. If a pin seems stuck, the guide has you remove the CPU and recheck. If activity starts and then suddenly stops, suspect the address decoder (U2), MMU (U3), the ROMs (U4, U5) or the CPU (U8).
- No video. Check the video waveform at the RF modulator input, transistor Q3, buffer U20, and GTIA pins 21–25. For colour faults, use the colour control R38: it should swing GTIA pin 17 from about 0 to 8.5 V. The manual's own adjustment is to turn R38 for a blue screen.
- No sound. Run
10 SOUND 0,100,10,15: GOTO 10and trace the signal from POKEY pin 37 through the audio amplifier to the modulator or monitor jack. - Keyboard. A table maps every key to the connector J8 pin and multiplexer (U24 or U25) it uses. If a whole group of keys fails, the faulty line is easy to find. If only one key is erratic, clean it.
- Paddles. A short BASIC loop prints
PADDLE(P)andPTRIG(P)for P = 0–3, which should run from about 228 down to 1. A further table maps each paddle and button to its POKEY and PIA pins. - Cassette. The guide traces SAVE and LOAD through POKEY pins 26–28 and the motor-control transistor Q7 driven by the PIA.
Disassembly and safety notes
Remove four screws from the bottom to lift the top. Seven more screws and a metal shield hold the board, with seven tabs twisted to hold the shield together. The safety page warns about static and soldering irons and says to keep peripherals unplugged from AC while working. As in Atari's own field manuals, the built-in Self Test (see XL/XE Self Test) is the first step in diagnosis.
Related
For the machine itself see Atari 130XE and its memory-management chip FREDDIE. Earlier machines are covered by Atari's own manuals: see 400/800 internal boards, 600XL internals and 1200XL internals.
Credits
- Picture: Sams Computerfacts CC16 for the 130XE. — Cover of Sams Computerfacts CC16 (Atari 130XE), scan from the local Atari documents collection
- Internet Archive item samscomputerfactstechnicalservicedataatarimodel130xecomputer1986sams (date 1986) — Internet Archive, 1986
