Atari 800 Troubleshooting (Sams Computerfacts CC7)
- Year
- 1984
- Type
- Component
- Category
- Third-party service data: power rails, chip map and fault-finding for the 800
- Manufacturer
- Howard W. Sams & Co. (service documentation for the Atari 800)
- Tags
- atari-800, service, repair, troubleshooting, sams, computerfacts, power-supply, ic-map, adjustments, 400-800
- Related
- Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual), Atari 800XL Troubleshooting (Sams Computerfacts CC11), Atari 130XE Troubleshooting (Sams Computerfacts CC16), Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21), Atari 810 Troubleshooting (Sams Computerfacts CD9), Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13)
Overview
Sams Computerfacts CC7 is the independent service folder for the Atari 800, published in 1984. Like other Computerfacts it combines schematics, annotated photos of every board, logic-probe readings, a parts list and a troubleshooting guide written for a TV-shop technician. It uses Atari's own board reference numbers. The motherboard parts are numbered from A101/Z101 and the CPU board parts from A301, the same scheme Atari's own field service manual uses (see 400/800 internal boards). That makes it easy to move between the two documents.
Chip map used in the guide
| Ref. | Part | Fault areas |
|---|---|---|
| A101 | POKEY | Keyboard (pins 16–25 scan, pin 29 key-pressed pulse), audio out (pin 37), cassette data (pins 26–28) |
| A102 | PIA | Joysticks, cassette motor control (pin 39) |
| A103, A104 | Motherboard ICs | Checked when CPU-board signals are good but video, data or external audio fail |
| A201, A202 | Voltage regulators | +24.4 V and +12.5 V rails on the power supply board |
| A301 | CTIA/GTIA | Colour (pin 21 output; pin 17 colour control voltage), sync (pin 25), console keys, keyboard-click pulses (pin 15), joystick triggers |
| A302 | ANTIC | Display data |
| A303 | CPU (6502) | Address pins 9–20 and 22–25, data, clock at pin 37 |
| Z103, Z104 | Keyboard multiplexers | A table maps every key to its Z103/Z104 pin |
| X101 | 3.579545 MHz crystal | Colour/clock oscillator (with transistor Q102) |
Checking the power supply
The 800's supply makes far more voltages than an XL, and CC7 checks them in order. It starts with 10.4 V AC from the external transformer at diode CR207, through the interlock switch S201 and power switch S202. Then come +12.5 V at regulator A202, +24.4 V at regulator A201, +11.8 V, −11.9 V at diode CR202, −5.0 V at zener CR201, and +5.1 V. For each rail the guide lists the diodes, capacitors and zeners to suspect if the voltage is missing or shorted to ground.
Typical faults
- CPU dead. Check the CPU's clock at pin 37, then the clock transistors Q102/Q103, and logic activity on the address and data pins.
- No video or sync. Trace from the RF modulator input back through the CTIA's outputs and ANTIC.
- No colour. Check CTIA pin 21 and the colour control R309. The voltage at CTIA pin 17 should swing from about 0 to 7 V as the control is turned. Then check the 3.579545 MHz oscillator.
- No speaker click. Run
10 PRINT CHR$(253): GOTO 10. Look for 1.4 V pulses at CTIA pin 15, then check transistor Q101 and the speaker. - No TV sound. Run
10 SOUND 0,100,10,15: GOTO 10and check POKEY pin 37. Check the 4.5 MHz sound oscillator (Q106) with a frequency counter and adjust coil L101 if it's off. - Recorder motor won't start.
POKE 54018,52should turn it on andPOKE 54018,60off. Check PIA pin 39 and transistor Q107. - Joysticks. A short BASIC loop prints
STICK(P)andSTRIG(P)for each port; the guide gives the expected values (15 at rest, 14 up, 13 down, 11 left, 7 right).
Adjustments and disassembly
- Colour: turn R309 for a blue screen on the monitor.
- Sound carrier: set L101 so the sound oscillator runs at 4.5 MHz.
- RF modulator: set the TV and channel switch S203 to channel 2 or 3 with AFC off, then adjust coil L210 for the best picture.
- Disassembly: five screws hold the cabinet bottom. The cartridge-door assembly, keyboard (four screws) and the heavy shield (nine screws) then come apart in turn. Before the main board and shield come out, cables J114 and J115 are unplugged from the power supply board (at J202 and J201).
Related
For later machines see 130XE troubleshooting (Sams CC16) and the 800XL Electronic Dimensions manual. For parts numbers see the 1983 service price list.
Credits
- Internet Archive item samscomputerfactstechnicalservicedataatarimodel800computer1984sams (date 1984) — Internet Archive, 1984
