Atari 1020 and 1027 Printer Field Service Manuals
- Year
- 1983
- Type
- Component
- Category
- Service documentation: the 1020 plotter and 1027 type-wheel printer, their tests and adjustments
- Manufacturer
- Atari, Inc.
- Tags
- 1020, 1027, printer, plotter, letter-quality, service, repair, field-service-manual, diagnostics, adjustments, atari-inc
- Related
- Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21), Atari 820 Printer Service Manual, Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13), Atari 410 and 1010 Program Recorder Service Manuals, Atari 835 Direct Connect Modem Field Service Manual, Atari 850 Interface Module Service Manual
Overview
Atari's Consumer Product Service wrote a Field Service Manual for every peripheral, and the two for its 1983 SIO printers follow the same layout. Each has eight sections: theory of operation, schematics and silkscreens, testing, diagnostic flowcharts, a symptom checklist, disassembly and assembly, a parts list, and a pocket for service bulletins (field change orders, upgrade bulletins and tech tips). The 1020 Color Printer manual is FD100288, Rev. 01, dated August 1983. The 1027 Printer manual is Rev. 01, dated October 1983. Both manuals concentrate on testing, cleaning and a few adjustments. Deeper mechanical faults are fixed by replacing the whole printer module or mechanism. For everyday use of the printers see Atari 1020 and Atari 1027.
The 1020: a plotter with two processors
The manual describes the 1020 as a free-standing, 40-column, four-colour printer averaging 12 characters per second. Its mechanism is an X-Y plotter that writes with four ballpoint pens. Inside:
- Two 8-bit single-chip microprocessors, each with its own 4 MHz crystal. A1 converts the 19,200 bit/s SIO stream into parallel data and reads the PAPER, COLOR and PEN buttons. A2, the printer controller, runs the firmware in its built-in ROM and drives the motors and pen solenoid.
- Motors. Two stepping motors, for the print head and paper feed, run in two-phase mode through an LB1257 driver. The basic step clock is about 4 ms.
- Pen up/down. An electromagnet with a permanent magnet. A pulse of about 5.4 ms flips the pen up or down, and the magnet or spring then holds it there with no current. A reed switch and a magnet in the rotary pen holder find the holder's "home" colour.
- Power. An external AC adaptor, with a bridge rectifier and two regulators (A5, A6) on the board.
The manual also explains some puzzling front-panel behaviour. PAPER, COLOR and PEN only work after the data received ends with a carriage return or line feed. Pressing PAPER and COLOR together performs a software reset to text mode.
Testing. At power-on the 1020 runs an internal test: the head moves to the far left, pauses, then draws four coloured boxes. The CPS Diagnostic Diskette (FD100577) holds T1020.BAS, loaded with RUN "D1:T1020.BAS". Its menu prints text and graphics samples, draws a straight line for pen up/down checks, spins the paper roller forwards and back, runs the carriage right and left, and steps the pen holder. Without the disk, a typed-in BASIC program sends command codes for 20, 40 and 80 columns and international characters. If a single command fails, the manual's advice is to swap A1 and A2.
Adjustments. With the pen down, the gap between the solenoid's actuator and coupling lever should be 0.1–0.2 mm. With the pen up, the stopper screw sets the pen-to-platen gap at 0.6–0.7 mm. Preventive maintenance is a dry-cloth clean, with alcohol or benzene for stains but never thinners. Then apply one small drop of light oil at specific points, such as the ejector shaft pivot and the ejection roller. To open the case, slide off the top cover, remove the two front rubber feet (the rear ones are glued), then remove the two screws under them and three more.
The 1027: a type wheel and an 8049
The 1027 is a letter-quality impact printer averaging 10 characters per second. A DC motor spins a type wheel, and a cam on the same shaft fires the hammer and advances the paper. Two pulse motors pull the wheel and the hammer along the carriage on wires. Two solenoids make the choices: solenoid A (pulse of about 8 ms) stops the wheel at the right character, and solenoid B (about 10 ms) selects the hammer. Photosensors read the character position and the home positions of the wheel and hammer, and an ink roll snaps onto a post in front of the wheel.
The controller is an 8049-family custom NMOS microprocessor with 2K of ROM and 128 bytes of RAM, clocked by a 6 MHz crystal. An LB1259 transistor array drives the motors. Power comes from a 9.5 V, 40 VA AC adaptor, regulated to 5 V for logic and 6 V for motors and solenoids.
Testing. T1027.BAS, on the same diagnostic diskette (Rev. 02), offers eight tests:
- An all-function test.
- The standard character set.
- The international character set.
- The standard character set with underlining.
- A direction print check of full-width lines in both directions.
- Continuous carriage returns.
- Continuous head travel, for scoping the motors.
- Repeating any chosen character.
A separate skew test prints 30 lines of the letter E. Draw vertical lines between the columns with a ruler. If the letters don't line up under each other on a second try, the mechanism is replaced.
Cautions. These matter more than any adjustment. Never oil or clean the type wheel. Don't touch the type-wheel shaft, because the manual warns that the acid in skin harms it. Use only single sheets of good 8½ × 11 unlined paper. Never print without paper, which damages the wheel and smears the next few sheets. The symptom checklist names the usual failures: dirt in the pulse-motor gears, a failed sensor unit, and the DC motor's capacitor lead coming off the motor terminal. Four screws hold the lower case, three hold the bezel, and one more sits between the I/O ports. Four more hold the mechanism, which unplugs from the board at three connectors.
Using them today
Both printers are now collector's items. The 1020's ballpoint pens and the 1027's ink rolls are the usual consumables to hunt for. The manuals' gap settings, lubrication points and type-wheel warnings are the most useful parts for anyone restoring one. For Atari's dot-matrix printer service data see 1025 service manuals.
Credits
- Picture: The 1020 Color Printer Field Service Manual, Rev. 01, August 1983. — Cover of the Atari 1020 Color Printer Field Service Manual (FD100288 Rev. 01, August 1983), scan from the Internet Archive (Fair use (cover of a service manual))
- Internet Archive item atari1020colorprinterfieldservicemanualrev.011983atari (OCR text) — Cover of the Atari 1020 Color Printer Field Service Manual (FD100288 Rev. 01, August 1983), scan from the Internet Archive (Fair use (cover of a service manual))
- Atari 1027 Printer Field Service Manual, Rev. 01 (Internet Archive, OCR text) — Internet Archive
