Atari 1200XL Internals (Field Service View)

Year
1982
Type
Component
Category
First single-board XL: memory, MMU, power supply and interfaces
Manufacturer
Atari, Inc.

Overview

The 1200XL, launched at the end of 1982, was Atari's first single-board computer. Its Home Computer Field Service Manual (Rev. 01) describes a machine that is clearly the ancestor of the 600XL and 800XL, but with several differences: it has no built-in BASIC, its power supply is inside, it has two extra LEDs, and its SIO port lacks power. This page follows the manual's "Theory of Operation" section. Compare it with the 600XL internals and the modular 400/800.

Board and console

One motherboard carries everything except the keyboard and LED display. The keyboard connects through a 15-conductor ribbon cable ending in a Molex connector. It feeds POKEY's keyboard scan lines (K0–K5, KR1, KR2), GTIA's console-key lines (S0–S2) and the CPU's RESET. The LED board has its own 5-conductor ribbon. The case has 54 full-stroke keys plus a space bar, and above them 11 function keys made of "brushed and formed aluminum nameplate material" under a translucent strip covering three LEDs: POWER, L1 (keyboard disabled) and L2 (international character set). The left side has the power switch, the single cartridge slot and only two controller jacks. The back has SIO, RF out, a monitor jack, the channel 2/3 switch and the power jack.

Main components

Block Detail from the manual
CPU 6502 (modified), i.e. SALLY
Custom chips ANTIC, GTIA, POKEY
PIA Port A reads the controller ports. On Port B, PB0 enables or disables the OS ROM, PB2 and PB3 drive LEDs 1 and 2, PB7 enables Self Test, and the rest are unused
OS Two 8K × 8 ROMs (16K in all), addressed by A0–A12
RAM 64K, organised as eight 64K × 1 DRAMs, one per data line; 48K directly available below the ROMs
MMU "Hard Array Logic" (HAL), a 3-to-8 decoder and a few gates. Inputs are A8–A15, ROM enable from the PIA and refresh. Outputs are the GTIA, POKEY and PIA chip selects, OS ROM select, RAM selects, cartridge selects and three "COMM" lines (A, B, C)
RF modulator Channel 2 (55.25 MHz) or 3 (61.25 MHz) video carrier, 4.5 MHz sound offset

Power: a linear supply on the motherboard

The 400, 800 and 1200XL take AC from the wall adapter; the 600XL/800XL and later machines take regulated 5 V DC. In the 1200XL a step-down transformer turns 115 V AC into 9 V AC, which enters through the power jack. The motherboard rectifies it with a bridge rectifier, and separate regulators feed separate power rails for different sections of the board, all with a common ground. Each regulator gives 5 V ±5% at up to 1.7 A, and the input power is 31 VA. See Atari power supplies.

SIO without power

The manual's SIO pin list shows two things that differ from the 800: pin 10 is just "Ready (Computer ON)", and pin 12, +12 V DC, is "not used on 1200XL". That's why SIO-powered gadgets such as the XC11/XC12 recorders, the XM301 modem and several printer interfaces need either the known board modification or a separately powered 1200XL version. The protocol is otherwise the familiar one: 19.2K baud maximum, LSB first, with command, acknowledge, optional data and complete frames. See SIO.

Why it matters for repairs and mods

  • The 64K×1 DRAMs and two-chip OS are different from the 800XL's parts. Use 1200XL-specific references when swapping chips or fitting 1200XL memory upgrades.
  • The PIA's PB2/PB3 LED lines are the same bits later used for RAM banking on the 130XE and in many XL memory upgrades. On a 1200XL, writing to them also lights the LEDs.
  • Owners fitting OS upgrades replace the two 8K ROMs (Atari's own service fix was the Rev. B pair). See Atari OS ROM.