Atari 600XL Internals (Field Service View)

Year
1983
Type
Component
Category
Single-board XL architecture: chips, MMU, memory and interfaces
Manufacturer
Atari, Inc.

Overview

The 400 and 800 were built from plug-in modules (see 400/800 internal boards). The 600XL shows how Atari redesigned the computer in 1983: one printed circuit board carries the CPU, RAM, the OS and BASIC ROMs, and all the I/O. The keyboard connects by a 24-way ribbon cable, power comes in through a 7-pin DIN socket, and peripherals use the SIO port or the new Parallel Bus Interface (PBI). The account below follows Section 1, "Theory of Operation", of Atari's 600XL Computer Field Service Manual (Rev. 1). The 800XL uses the same design with 64K on board.

The digital hardware

Part What the manual says
6502C CPU The modified 6502 (Atari's SALLY), with a HALT input so ANTIC can take the bus
ANTIC "A custom display microprocessor with an instruction set customized for graphics generation", which also controls the address and data buses and RAM refresh
GTIA Turns ANTIC's data stream into colour and luminance, reads the console function keys, drives the keyboard "beep" and watches the joystick triggers
POKEY Sound, SIO data and clocks, paddle (pot) scanning and keyboard scanning
PIA Watches the controller ports and SIO control lines, drives the LED, enables Self Test, and "in certain applications may control the MMU logic"
OS ROM One 16K × 8 ROM, addressed by A0–A13
BASIC ROM Atari BASIC Revision B in an 8K × 8 ROM, "equivalent to having an Atari BASIC cartridge permanently plugged into the console"; any real cartridge takes precedence
RAM Two 16K × 4 dynamic RAMs, giving 16K, expandable to 64K with the 1064 module on the PBI
MMU A PAL (programmable array logic) chip, a 3-to-8 decoder and a few gates. Its inputs are address lines A8–A15 plus control signals such as ROM enable (from the PIA) and DRAM refresh (from ANTIC). It produces the select signals for GTIA, POKEY, the PIA, the OS ROM, the DRAMs, BASIC and the cartridge
Delay line Part of the "miscellaneous logic" alongside the MMU

The manual's block diagram labels the PIA path "ROM Self Test Enable and BASIC Enable". This is the start of the XL's PORTB-controlled memory scheme, later extended for banked RAM on the 130XE.

Interfaces

  • SIO: asynchronous serial, up to 19.2K baud, LSB first, with a start and a stop bit. The computer always starts the exchange: command frame, acknowledge, optional data frame, then complete. The 13-pin connector carries clock in/out, data in/out, command, motor control, proceed, +5 V/Ready, audio in and interrupt (pin 12 is not connected). See SIO.
  • Controller jacks: two identical 9-pin ports (four directions, trigger, two potentiometer inputs, +5 V and ground).
  • Cartridge: the 30-pin slot, with S4/S5 selects, RD4/RD5, the CCTL control line and Phase 2. Inserting a cartridge disables built-in BASIC in hardware.
  • Keyboard: 55 keys plus space bar, scanned through two decoders (U22, U23), plus four function keys and RESET.
  • PBI: the expansion connector "for future peripherals", which the 1064 memory module uses. See Parallel bus interface.

Power and RF

The external supply takes 110 V AC and gives +5 V DC ±2% at up to 1.5 A through the DIN plug. The RF modulator combines composite video and mono audio onto channel 2 (video 55.25 MHz, audio 59.75 MHz) or channel 3 (61.25/65.75 MHz), with a 4.5 MHz sound carrier.

Console keys, as Atari described them

The manual notes two start-up behaviours. Holding OPTION at power-on disables the built-in BASIC. If there's also no cartridge or disk, the Self-Test menu appears. HELP returns from an individual self-test to the menu and was reserved "for future software development"; the manual warns that it doesn't work the same way as on the 1200XL. See XL/XE Self Test and Atari 600XL.