Atari 835 Direct Connect Modem Field Service Manual
- Year
- 1983
- Type
- Component
- Category
- Atari service documentation: 835 modem theory, Bell 103 tones, the TEST835 diskette and fault flowcharts
- Manufacturer
- Atari, Inc.
Overview
The Atari 835 was Atari's first SIO modem: a 300-baud, Bell 103, direct-connect unit sold with the TeleLink II cartridge. Its Field Service Manual (FD100268, Rev. 01, March 1983) is short but complete. It has six sections: theory of operation, schematic and silkscreen, testing, flowcharts, parts list and service bulletins. Service centres were told to ask customers to send in three things together: the modem, its power adaptor and the TeleLink II cartridge, because the unit couldn't be fully tested without all three. The manual also lists the 835's features: automatic pulse dialling, originate/answer switching under software control, and the ability to listen to the phone line through the TV speaker.
Inside the 835
| Block | Part | Job |
|---|---|---|
| SIO interface | Two 13-pin sockets and an LM339 comparator (M6) | Pins 2, 5, 7 and 10 from the computer pass through the comparator, which acts as a latch. Pins 3, 9 and 13 go straight back from the controller |
| Controller | Intel 8048 with Atari firmware (M5) | Translates computer commands. Passes data both ways at 300 baud. Drives the hook relay, LEDs and audio monitor. Tests itself and the modem chip at power-up |
| Modem chip | Texas Instruments 99532 (M4) | FSK modulation and demodulation, plus carrier detect |
| Line interface | Op-amp M2, multiplexer M3, transformer T1, relay K1 | Separates received signals from the modem's own transmit signal, isolates the line, and switches on- or off-hook |
| Power | 22 V AC adaptor | Gives about +18 V (relay and LED drive), +12 V and −5 V (modem chip), and +5 V (logic) |
The controller talks to the computer using SIO signalling at 300 baud, and to the modem chip using a "modified RS-232C" link, also at 300 baud. Its commands go on-hook or off-hook, pulse-dial (relay timing meets FCC and Canadian rules), choose originate or answer (originate is the default), send or receive a character, report status, switch the line audio to the TV, and start an analog loopback. In loopback the 99532's transmitter is wired to its own receiver and cut off from the line.
The Bell 103 tones are set out exactly. In originate mode the 835 sends 1270 Hz for a 1 bit and 1070 Hz for a 0, and listens for 2225/2025 Hz. In answer mode it sends 2225/2025 Hz and listens for 1270/1070 Hz. The carrier-detect line lights the On-Line LED.
The test procedure
The bench setup was a 400 or 800 with BASIC, an 810 drive and Atari's test diskette. When the 835 is powered up, the Power LED should stay lit, the On-Line LED should flash once and the relay should click once. Booting the disk loads the 835 handler. Then type RUN "D1:TEST835" to bring up an option menu:
- TV sound and direction. Turn the line audio on and hear a high tone in answer mode and a low tone in originate mode.
- Off-hook / on-hook. Each press of key 3 should click the relay.
- Carrier wait. Key 9 goes off-hook and shows WAITING FOR CARRIER for 30 seconds, then hangs up.
- Autodial. Key 7 first shows a warning about "Horizon" phone systems. With no line connected, option 1 dials a test number: after a three-second pause for dial tone, the relay pulses, short for the digit 1 and longest for 0.
- Analog loopback. The screen turns grey and shows CARRIER, the On-Line LED lights, and the data sent and received should match.
If any step fails, an alphabetical set of flowcharts takes over. One example asks whether transistor Q1's collector swings between about +19 V and −5 V, and says to replace Q1 if it doesn't. Finally, the technician checks that the customer's TeleLink II cartridge works and is being used as its manual describes.
The Horizon warning
The manual repeats one warning in capitals. Don't connect the 835 to Bell's "Horizon" system, a four-wire, non-standard business phone system that accepted only touch-tone dialling. Doing so "damages the telephone system". It's a reminder that the 835 can only pulse-dial.
Using one today
Real 835s still work on analogue lines at 300 baud, but they need software written for the 835's own command set, such as TeleLink II, rather than Hayes AT commands. For a Hayes-style connection to modern telnet BBSes, see internet and Wi-Fi modems. Atari's later SIO modems are the 1030, XM301 and SX212.
