Atari 820 Printer Service Manual

Year
1982
Type
Component
Category
Atari service documentation: the 820's cam-driven mechanism, 6507 controller, quick-check program and repairs
Manufacturer
Atari, Inc.
Yellow cover of the Atari 400/800 '820 40 Column Printer Service Manual', with a faded photo of a family around a television

Overview

The Atari 820 was one of the first printers for the 400 and 800: a 40-column impact printer on a narrow paper roll. Atari's 820 Printer Service Manual (copyright 1982) is written in a formal style, with numbered paragraphs, a list of effective pages and "Notice of Changes" update sheets. It covers the printer down to the replaceable-chip level and promises that "none of the procedures included require special test equipment or tools". It has six chapters: general information and specifications, installation, operation with the 400/800, a functional description, maintenance and repair, and spare parts. Two scans of it survive: the field service manual FD100048 and a copy titled 400/800 820 40 Column Printer Service Manual. Their tables of contents are identical.

Specifications

Print area 3⅓ inches wide, 40 columns at 12 characters per inch
Line spacing 6 lines per inch
Font 5 × 7 dot matrix
Print cycle 800 ms per line
Head sweep 10.75 inches per second
Margin repeatability ±0.015 inch
Vertical dot alignment ±0.0025 inch
Controller 6507 CPU, 6532 PIA, ROM, 1 MHz crystal clock
Power Built-in 120 V AC cord, with separate fuses for mains and print-head current

How the mechanism works

Nearly everything in the 820 is driven by one motor and one cam.

  • Drive. A motor turns an elliptically slotted drive cam through a belt. The cam sweeps the head across the paper and back. A Print OK microswitch riding on the cam tells the controller when the head enters the print area and when it is home.
  • Paper feed. An eccentric on the cam works a pawl against ratchet teeth on the platen, so each full turn of the cam advances the paper one line. A pressure roller underneath holds the paper against the platen.
  • Ribbon. A grey feed lever on the head has a pawl at each end. As the head moves, the pawl turns one spool's ratchet. When the ribbon runs out, the lever is pushed over and the feed reverses.
  • Head. Seven print solenoids form a vertical column, numbered 1 at the top to 7 at the bottom.

The 6507 watches the 6532 for data from the computer, answers SIO commands, turns characters into dot patterns, and drives the motor and solenoid drivers through transistor arrays and solid-state relays.

Testing

The Operator Interactive Test needs no computer: switch on and press PAPER ADVANCE. For a full check, Atari supplied a BASIC Printer Quick Check program. It prints a title, the upper- and lower-case alphabets, digits and punctuation, a repeated "HELLO ATARI 820 PRINTER USER" line and a rolling character pattern, ending with "End of Printer Quick Check". The technician compares the strip with a sample printout. The program can be run from cassette, disk or a printed listing.

Maintenance

To clean the printer, remove the cover, paper and housing. Wipe the mechanism with isopropyl alcohol to remove old grease, clean the platen, then take out the two hex screws on each side and clean the head and its shaft. Regrease sparingly with IBM #23 or Lubriplate #70: "enough to create a film". The points to grease are the cam groove, the guide the head's "tail" runs in, the paper-feed cam and pawl, the platen detent and ratchet teeth, and the pressure-roll release lever.

The visual inspection list includes several tests worth repeating on any 820:

  • Press PAPER ADVANCE and watch all seven print wires move.
  • Turn the cam by hand toward the platen only and listen for the Print OK switch. It should click halfway up the cam's high ramp.
  • The plastic paper-guide strip must touch the platen along its whole length.
  • Both ribbon-reverse springs must be in place and of equal tension.

Head alignment is needed whenever the head screws are loosened. With no paper or ribbon fitted, set the head-to-platen gap with a feeler gauge to 0.012–0.015 inch, checking it across the full width before tightening. The manual warns that turning the cam backwards can damage the Print OK switch.

The troubleshooting table

The manual's Table 5-1 lists 14 symptoms. Highlights:

Symptom Likely causes
No power light, no paper advance Blown fuse, broken fuse holder, transformer
Paper advances continuously at power-up Transistor array, solid-state relay, Print OK switch
No response to the computer (ERROR 138) Among others, a transistor array
Head moves but doesn't print Blown fuse, broken fuse holder, transformer, main board
Head vibrates at home Solid-state relays, transistor arrays
Missing dots Transistor array, driver, print head
Motor stalls Belt tension, motor
Uneven line feeds Belt, paper slippage (clean the platen), feed parts
Characters vary in width Belt tension, head binding on its guide bar (clean and lubricate)
Ribbon snags on the head Wrong head-to-platen gap

Chips are replaced using a "chipping chart" of the main board. They sit under a noise shield held by five bendable tabs. The manual also gives full procedures for replacing the transformer, board, head, Print OK switch and drive belt.

Credits