Atari 1030 Direct-Connect Modem

Year
1983
Type
Peripheral
Category
Modem (300 baud direct-connect, SIO)
Manufacturer
Atari, Inc. (modem electronics by Penril)
Atari 1030 modem in its XL-style case

Overview

The 1030 was the modem that made telecommunications a plug-in-and-go affair on the XL computers. It connects to the SIO bus and directly to a modular phone line, needs no 850 interface, and — its cleverest trick — carries its own software. With no disk drive switched on, the 1030 answers the computer's boot request as if it were disk drive 1 and loads ModemLink, a terminal program with an integrated T: modem handler, from its ROM into the computer; a long beep sounds while it loads. Alternatively, the T: handler alone can be loaded from the modem later for use with other software.

It is a 300-baud Bell 103 modem, functionally an improved 835: software selects full or half duplex, originate or answer, pulse or tone dialling, a memory buffer and printer echo. It communicates with both originate-only and answer-only modems.

Specifications

Item Detail
Speed / standard 300 baud, Bell 103
Dialling Pulse or tone (tone not available on the Atari 400)
Electronics Intel 8050 microcontroller; 12 KiB firmware (4 KiB in the 8050, 8 KiB external ROM); TI TMS99532 modem chip
Software in ROM ModemLink terminal program and T: handler, downloadable over SIO
Indicators Power and on-line (carrier detect) LEDs
Receive sensitivity −43 dBm
Connection 2 SIO ports (3-ft SIO cable included); RJ11 phone jack plus built-in cable to the telephone
Power 9 V AC from Atari C062195 adapter
Manual The Atari 1030 Modem with ModemLink Telecommunications Program Owner's Guide C061798 (1983)

History

In March 1983 the Washington Post reported that Penril Corp. had won a $4 million contract to supply about 100,000 low-cost modems — the 1030 — to Atari, with deliveries starting in July 1983. Atari introduced the 1030 with ModemLink at the June 1983 Summer CES for autumn release. Boxes carried free-time offers for Dow Jones News/Retrieval, and CompuServe IntroPaks were included. Its designers were project director Sherwin Gooch with John Curran, Ken Fowkes, Joe Miller, Songly Mu, Bernie Poggi, Mark Rustad, Phil Schug, Dennis Smith, Jose Valdes and Vince Wu. The 1030 was succeeded in 1985 by the cheaper, SIO-powered XM301, which is software-compatible with it; Antic's 1988 shopper's guide called the XM301 a "worthy successor to the Atari 1030".

How it works

The 1030 is one of the few devices that uses the SIO proceed and interrupt lines. Its commands are not standard SIO frames but single bytes sent at 300 baud while the command line is asserted; once the modem is "resumed", data flows directly over the bus at 300 baud and the SIO bus is effectively dedicated to the modem until it is suspended again. Tone dialling is done by the computer: POKEY generates the touch-tones in volume-only mode and they reach the modem through the SIO audio input line.

Using it today / Known issues & tips

  • Software support. Because of its non-standard protocol, terminal software must explicitly support the 1030. Well-supported options included Keith Ledbetter's Express! (a dedicated 1030/XM301 version) and BBS Express!, and Russ Wetmore's article "Unleashing the 1030 Modem" (Antic, August 1985) documented how to control it directly.
  • Check the power adapter. Antic's 1988 SX212 review singled out the power supply as "a weak point of the Atari 1030 modem"; test or replace the C062195 9 V AC adapter before blaming the modem.
  • 130XE banking. Bill Wilkinson warned that careless PORTB bank switching on a 130XE can disrupt the 1030's carrier detection.
  • Emulation. Altirra emulates the 1030, including booting ModemLink from the internal firmware, real pulse and tone dialling, and full hardware emulation.

Credits