Atari 810 Troubleshooting (Sams Computerfacts CD9)
- Type
- Component
- Category
- Third-party service data: 810 disk drive fault-finding
- Manufacturer
- Howard W. Sams & Co. (service documentation for the Atari 810)
- Tags
- atari-810, disk-drive, service, repair, troubleshooting, sams, computerfacts, stepper-motor, drive-motor, 6507, fd1771
- Related
- Happy 810 Enhancement, Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13), Atari 130XE Troubleshooting (Sams Computerfacts CC16), Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual), Atari 800 Troubleshooting (Sams Computerfacts CC7), Atari 800XL Troubleshooting (Sams Computerfacts CC11)
Overview
The Atari 810 is a computer in its own right. A 6507 CPU with its own ROM, RAM and timer runs the drive, a PIA links it to the Atari's serial bus, and a floppy-disk controller drives the head electronics, the drive motor and the stepper motor. Sams Computerfacts CD9 documents it the same way Sams covered TVs: full schematics (including the optional External Data Separator board), photos of the side (CPU) board, rear (analog) board and power supply, parts lists, waveforms, and a troubleshooting guide. The guide is written for an 810 connected to an Atari 400 or 800.
Block diagram and signals
The CD9 block diagram runs computer → PIA → CPU, with the CPU served by ROM, RAM and a timer and connected to the controller. The controller drives the read/write head (through write amplifier, read preamp and read amplifier) and the two motor drivers for the stepping motor and the drive motor. The line-definition table lists the drive's control signals, among them DRQ (data request), DINT (disk initialization), HLT (head load timing), TR00 (track 00 sensor), WD and WG (write data and write gate), WF (write fault), WPT (write protect), RE (read enable) and an index-pulse line.
Troubleshooting steps (as in CD9)
| Area | What to check |
|---|---|
| Power supply | About 10.9 V AC at the power-pack plug. Then 12 V at the cathode of CR111. If it's missing, check connector J110, diodes CR111–CR114 and regulator A108; if present, check 5 V at A108 pin 3. If 12 V is low, check error-amp transistors Q114/Q115 and regulator transistor Q113. Check −5 V at zener CR115/CR116 and the power LED (CR108) |
| CPU (A101) | Reset at pin 1 should be low for about 0.2 s at power-on, then go high; if not, check reset transistors Q110/Q111 and R175. Look for the 0.534 MHz clock at pin 27, and 1 MHz at Z101 pin 11 from crystal X101 and clock amp Q101. Then check the data and address pins for pulses |
| Drive motor won't run | Connector J103. About 1.1 Ω between its pins 3 and ground. Motor windings: 7.8 Ω between pins 3 and 4, 9.1 Ω between 4 and 5, 178.5 Ω between J105 pins 1 and 3. Then about 0.1 V at PIA (A104) pin 25 at rest, 5 V when running |
| Motor good but still dead | Logic on PIA pin 14 (low at rest, high running); then the controller (A105), CPU (A101) and ROM (A102) |
| Stepper won't step | 12 V at J102 pins 1–5, then pulses at J106 pins 1–4. Windings should be 75 Ω between pin 5 and each of pins 1–4 |
A short BASIC program writes and reads a test file (D:SAMS.FIL) so the waveforms can be checked while the drive works:
10 PRINT "THIS IS A DISK TEST"
20 OPEN #7,8,0,"D:SAMS.FIL"
30 FOR X=1 TO 200
40 PRINT #7;"THIS IS A DISK TEST"
50 NEXT X
60 CLOSE #7
70 GOTO 10
Disassembly order
- Cabinet: remove four rubber feet and four Phillips screws, then lift off the top.
- Base plate and front panel: five screws hold the base plate to the cabinet bottom. Remove the front panel from the base plate.
- Side (CPU) board: unplug J101 (write protect) and J102 (stepping motor), remove three screws holding the board and ground shield, and lift it up until J106 is disconnected from the rear board.
- Rear (analog) board: unplug J103 (drive motor) and J109 (head I/O), remove four screws, and lift the board while pulling out the right side to free J10 and J105.
The manual also has the usual tables of DOS error codes (138 device time-out, 144 disk error, 162 disk full, 167 file locked and so on) and a reminder to format disks from DOS menu option I.
Related
For hardware revisions and upgrades see 810 upgrades and Happy 810 enhancement. Similar Sams folders exist for the 800 and 130XE.
Credits
- Picture: Sams Computerfacts CD9 for the Atari 810. — Cover of Sams Computerfacts CD9 (Atari 810), scan from the local Atari documents collection
