Atari 810 Revisions: ROMs, Data Separator, Analog Board and Tandon Mechanism

Year
1981
Type
Upgrade
Category
Factory revisions and Atari upgrade kits for the 810 disk drive (1980–1983)
Manufacturer
Atari, Inc.
Front and rear views of an Atari 810 disk drive, with a lift-up front latch and the two I/O connectors and drive-code switches at the back

Overview

The Atari 810 was the 8-bit line's first disk drive and it changed more during its four-year life than any other Atari peripheral. Field reports of read errors and speed drift led Atari to revise its electronics twice, rewrite its firmware, and finally swap the drive mechanism — and to sell most of those changes as upgrades for drives already in customers' homes. As a result, two 810s from different years can differ in almost everything but the case. This entry is a guide to those revisions; for the drive in general see the main 810 entry.

The revisions at a glance

Version Date How to recognise it What changed
Original (pre-Analog, no data separator) 1980–81 MPI mechanism with push-button door; side board and rear board 20 W, ran from the early small CA014748 supply
Data Separator ("DS") From 1 Sept 1981 "DS" sticker External Data Separator board plugged into the floppy-controller socket on the side board; stepper circuit regulated at 12 V; 21 W
ROM C November 1981 "C" sticker Faster sector order when formatting
810 Analog ("810M Analog") From February 1982 Power-supply board in place of the rear board; analog board on top of the mechanism Tachometer speed control and redesigned read/write circuits; 30 W
810T Analog From November 1982 Lift-up front latch instead of a door button Tandon mechanism replaces MPI

Data separator

A floppy controller must separate the clock pulses from the data pulses in the stream coming off the head; marginal separation causes misreads. From September 1981 Atari fitted an External Data Separator Board, which plugs into the side board where the FD1771 floppy-disk controller chip would otherwise be installed. It was sold as an upgrade too, though early side boards had to be modified first. Atari's own HCD Diagnostic Kit for service centres included a replacement side board with data separator (CA014834, $49 to an authorised servicer).

ROM revisions B, C and E

All 810 firmware ROMs are 2 KiB. Three versions are known:

  • Revision B — the early ROM. It formats tracks with a slow sector order, about 13 sectors apart.
  • Revision C — the common ROM from November 1981. The only change is the formatting order: odd sectors first, then even, about 9 sectors apart. Because sending a sector to the computer at 19,200 baud takes about 95 ms, during which nine sectors pass under the head, the new order lets the drive pick up consecutive sectors without waiting a full revolution; Antic reported it about 20% faster. Atari offered ROM C as an upgrade and, for owners of older drives, sold the CX8111 Formatted Diskette II, already laid out in the faster pattern. Rev. C also has a harmless bug: it accepts command $4F as a synonym for Write.
  • Revision E — rarer. It fixes the $4F bug, reports controller status uninverted and adds commands that let the computer download and run code in the drive ($20 to execute a 128-byte routine, $54 to read drive memory, $FF to call pre-loaded code).

The Analog board set

The February 1982 redesign aimed at reliability, above all motor speed and reading. A new Power Supply Board replaced the rear board and added a tachometer circuit (a frequency-to-voltage converter) to hold the motor at 288 RPM. A new Analog Board, bolted to the top of the mechanism, took over the read/write electronics, using op-amps and discrete transistors instead of transistor arrays and a multiplexer chip to switch the amplifiers; a 10-pin ribbon cable joins the two. The three parts were sold together as the CB101128 "Grass Valley Analog Board Set" to upgrade pre-Analog drives.

MPI versus Tandon

In November 1982 Atari switched the mechanism from Micro Peripherals, Inc. (MPI) to Tandon, creating the 810T. The two need different service procedures:

Tandon (810T) MPI (earlier drives)
Front Lift-up front latch, no eject Door-release button with eject mechanism
Head load arm No pressure spring; adjusted with two nuts Pressure-spring assembly
Stepper adjustment Cam screw at rear Loosen setscrew, move stepper band pulley
Track 00 stop Set by watching waveform amplitude Set to 0.010-inch clearance
Write-protect sensor Microswitch Phototransistor

Using one today

  • Check the stickers and the boards. A "DS" sticker, a "C" sticker, an analog board on the mechanism and the front latch style tell you which upgrades a drive has.
  • Formatting order stays with the disk. A disk formatted on a Rev. B drive keeps its slower sector order whichever drive reads it; reformatting it on a Rev. C drive gives the faster layout.
  • Power: pre-DS drives were specified for the early 20 W supply, Analog drives need the 31 VA CA017964 type; using the larger supply is always safe.
  • Speed: pre-Analog drives lack the tachometer regulation, so checking that the disk turns at 288 RPM is a sensible first step when an old 810 misreads.
  • Third-party upgrades (Happy, Fast-Chip and others) were built to fit particular revisions — the Happy 810 came in versions for no-separator, separator and Analog drives.

Credits