Atari 810 Disk Drive

Year
1979
Type
Storage
Category
5.25-inch floppy disk drive (single density)
Manufacturer
Atari, Inc.
Beige Atari 810 floppy disk drive with push-button door

Overview

The 810 was the disk drive that turned the Atari 800 into a serious computer. Previewed in January 1979 and shipped in November–December 1979 at $749.99, it connects through the SIO serial bus and contains its own microprocessor, so the computer simply asks for numbered sectors and the drive handles motors, seeking and formatting itself. Its format — 40 tracks of 18 sectors of 128 bytes, 720 sectors and 90 KiB per side — became the baseline "single density" format that every later Atari drive, DOS and disk image supports. Up to four 810s can be daisy-chained, selected by two rear switches.

Specifications

Item Detail
Capacity 40 tracks × 18 sectors × 128 bytes = 720 sectors, 92,160 bytes (90 KiB) per side
Encoding FM (single density), 48 TPI, one head (reads the underside of the disk)
Rotation 288 RPM ±1%
Performance Average transfer 6000 bit/s; average access 74 ms; track-to-track 5 ms
Controller 6507 CPU at 500 kHz, 2K ROM, 6810 RAM, 6532 RIOT, Western Digital FD1771 FDC at 1 MHz
SIO Commands at 19,200 baud; status, read, put, write-with-verify, format
Connection 2 SIO ports; drive-number switches (drives 1–4)
Power 9 V AC (CA017964); 20–30 W depending on version
Media Any 40-track 48 TPI 5.25" disk (SD/DD/QD); not high-density disks

Revisions

The 810 changed a great deal over its life:

  1. Original (1980–81) — MPI drive mechanism, side and rear circuit boards, no data separator.
  2. Data separator (from 1 September 1981, "DS" sticker) — an external data separator board fitted in the FDC socket improves the drive's ability to tell data pulses from clock pulses; also sold as an upgrade.
  3. ROM C (November 1981, "C" sticker) — formats disks with an improved sector layout, reported about 20% faster; CX8111 pre-formatted disks provided the same layout to older drives.
  4. 810 Analog (February 1982) — new power-supply board with a tachometer circuit to stabilise speed and a new analog read/write board; offered to older drives as the "Grass Valley Analog Board Set".
  5. 810T Analog (November 1982) — Tandon mechanism with a front latch in place of the MPI push-button door.

The case was designed by Roy Nishi and Russ Farnell. Early drives shipped with the 810 Master Diskette (DOS I); from 1981 they came with Master Diskette II and DOS 2.0S. The planned double-density 815 dual drive never shipped, and the 1050 replaced the 810 in mid-1983.

Using it today / Known issues & tips

  • Clean the head and pad. Atari's field service manual notes that both the head and the pressure pad collect oxide and dirt, and recommends a cotton swab moistened with methyl or high-quality isopropyl alcohol — never carbon tetrachloride — and keeping magnetised tools away from the head.
  • Speed matters. Many read errors on old drives are speed or alignment problems; the FSM procedure uses an alignment disk or cartridge.
  • Power on the drive first, then insert the disk; remove the disk before switching off.
  • "Flippy" disks. The 810 ignores the index hole, so the back of a disk can be used by notching it and inserting it upside down.
  • Upgrades. The Happy 810 Enhancement, the Archiver "Chip", Fast-Chip and the 810 Turbo (double density) were the classic third-party add-ons.
  • Emulation. Altirra offers full 810 drive emulation (running the real firmware) as well as fast standard emulation; one firmware quirk it reproduces is that the 810 accepts $4F as an alias for the write command.

Compatibility

All Atari DOSes read 810 single-density disks, and the 1050, XF551 and virtually all third-party drives are backward compatible. The 810 cannot read the 1050's 130K enhanced density or 180K double-density disks.

Credits