Atari 800XL Troubleshooting (Electronic Dimensions Service Manual)

Type
Component
Category
Third-party service manual: 800XL theory, chip map and symptom chart
Manufacturer
Electronic Dimensions (San Luis Obispo, California)

Overview

Electronic Dimensions of San Luis Obispo, California published a Service Manual for the Atari 800XL Computer: a 41-page booklet with the familiar five sections of Atari's own field service manuals. They are (1) theory of operation, (2) self testing, (3) disassembly and assembly, (4) troubleshooting and (5) schematic and parts list. Its theory section follows the structure and much of the wording of Atari's 600XL field service manual, adjusted for the 800XL. What makes it useful today is the troubleshooting chart, which lists faults "in the most common order of failure" and links each one to specific parts on the 800XL board.

What it says about the hardware

  • RAM: eight 64K × 1 DRAMs (64K on the board, against the 600XL's two 16K × 4 chips).
  • MMU: a PLA (programmable logic array), a 3-to-8 decoder and a few gates. Inputs are A8–A15 plus ROM enable from the PIA and DRAM refresh from ANTIC. Outputs are the selects for GTIA, POKEY, the PIA, the OS ROM, the DRAMs, BASIC and the cartridge.
  • ROMs: one 16K × 8 OS ROM (A0–A13), and Atari BASIC Revision B in an 8K × 8 ROM that any plugged-in cartridge overrides.
  • Ports: a 5-pin DIN monitor jack in addition to RF, the PBI, SIO, two controller jacks and one cartridge slot.

The troubleshooting chart (selected)

Symptom Possible causes What to do
Snowy screen TV switch box, channel switch, RF modulator; power supply or RF cable; open or shorted parts on the +5 V lines; shorted LSI chips Adjust, isolate and replace
No colour or bad colour RF modulator or colour control R38; U17 (GTIA), U20, Q1, Q3, CR2, CR3; crystal Y1 Check Y1 runs at 3.579545 MHz
Black or grey screen Clock parts Y1, Q8, Q9, C109; or U2, U7–U20, U22, U23, U26–U30 Troubleshoot the clock, then isolate the IC
Yellow screen U28 Replace
Blue screen U2 Replace
Red/brown screen U2–U5, U18, U19, U28, U30 Isolate and replace
CPU test fails Y1, Q8, Q9, U8 Verify the 3.58 MHz oscillator
RAM test fails U2, U3, U9–U16, U18, U19, U26–U30 Verify ANTIC is Rev. E, then repair
ROM test fails U2–U5 Repair or replace
ANTIC or GTIA test fails U7 (ANTIC), U17 (GTIA) Replace
Console keys dead U17, keyboard, cable —
Tones missing in tone test U22 (POKEY), RF modulator 4.5 MHz sound carrier, TV volume Adjust the 4.5 MHz carrier
Upside-down characters on the player field U7 Replace
Some or all keys fail U22, U24, U25, keyboard, cable —
PIA port, SIO, pot-line and trigger failures U23 and U22 with their filter parts (C/L networks) Repair or replace

Several tests in the chart (the two-way clock test and external audio) "require the SuperSALT Test Assembly, jumper cables, power supply", that is, Atari's own SuperSALT diagnostic kit. Others use the computer's built-in Self Test. The manual describes the memory test, the audio-visual test (six tones over four channels, where a note with no sound or a sound with no note marks the fault), the keyboard test and "All Tests".

Disassembly

Remove six screws from the bottom, lift the left side of the top cover to reach the keyboard cable, and disconnect the ground strap and cable. Then remove four more screws and lift the front of the board while pushing out the right side of the bottom housing until the player ports clear. The manual warns not to swap top and bottom housings between units, because the plastics aren't interchangeable.

Related

For the 130XE equivalent see 130XE troubleshooting (Sams CC16). For the machine see Atari 800XL. The "ANTIC Rev. E" note refers to the XL-era ANTIC described in ANTIC.