Connecting an Atari 8-bit to Modern TVs and Monitors

Rear panels of an Atari 800XL stacked above a 130XE, showing their ports

The Atari 8-bits were designed for 1980s analog TVs. Getting a sharp, stable, lag-free picture on today's sets takes a little planning: picking the best output your model has, wiring the right cable, matching the video standard, and taming modern TV processing. This guide works through it model by model.

What you'll learn: what RF, composite and S-video (Y/C) mean for an Atari, which outputs each model has, the monitor-port pinout, how to wire a cable, the PAL/NTSC/SECAM traps, why NTSC "artifact colours" vanish over S-video, and how to deal with HDTV lag.

What you need: your Atari, a display with composite and/or S-video inputs (or a converter for HDMI-only sets), and the matching cable. For a DIY cable you'll need a 5-pin 180° DIN plug and phono (RCA) plugs.

1. Three kinds of signal

Some background:

  • RF is audio and video modulated onto a TV channel, made for the antenna input. It's the lowest-quality option and only works on sets that still have an analog tuner for the matching standard.
  • Composite video carries brightness (luma, "Y") and colour (chroma, "C") mixed in one signal, without audio. It's better than RF, and in the 1980s monitors with composite inputs were prized because they beat TVs on picture quality.
  • Y/C, also called S-video, keeps luma and chroma on separate wires. It is superior to composite and ideal for the Atari; savvy users of the time sought such monitors out.

2. What your model can output

Video outputs by model:

Model (NTSC unless noted) RF Composite Luma (Y) Chroma (C)
400, NTSC 600XL yes (ch. 2/3) – – –
800 yes yes yes yes
1200XL, NTSC 800XL yes yes yes no
65XE, 130XE yes yes yes yes
XE game system yes yes (phono jack) – –
PAL 600XL yes (ch. 4 or 36) yes – –
Earlier PAL 800XL yes yes yes no
Later PAL 800XL, PAL 800/65XE/130XE, 800XE yes yes yes yes
SECAM 800XL/130XE/XEGS no RF SECAM composite – –

So the 800, 65XE, 130XE, 800XE and later PAL 800XLs can give true S-video straight from the monitor port. The 1200XL and NTSC 800XL offer composite and luma only. The 400 and NTSC 600XL are RF-only, and the XEGS has composite and audio on two phono jacks instead of a monitor port.

3. The monitor port pinout

All models with a monitor port except the SECAM ones use a 5-pin 180° DIN socket. Pin functions:

Pin Signal
1 Composite luminance (Y). PAL 600XL: not connected
2 Ground
3 Audio out
4 Composite video (NTSC or PAL)
5 Composite chrominance (C). 1200XL, NTSC 800XL, earlier PAL 800XL: not connected; PAL 600XL: ground

Antic's Pinout Master Charts (Tech Tips, March 1987) drew every 8-bit connector as seen looking into the socket. Use that view, or a continuity tester, so you don't wire a mirror image. SECAM machines use a 6-pin DIN with SECAM composite and Peritel (SCART) support lines, and their own cable.

4. Choosing and building a cable

  • Composite plus audio (two phono plugs): like Atari's CX89 colour monitor cable. Wire pin 4 to video, pin 3 to audio, and pin 2 to both grounds.
  • Monochrome: Atari's CX82 black-and-white cable uses pin 1 (luma) instead of pin 4. Text on a green or amber monitor is sharp, but colour games turn into shades of one colour.
  • The "universal" four-plug cable carries audio, composite, Y and C. Atari never made one. With it you can feed a Y/C monitor, a composite set or a mono monitor from the same lead.
  • S-video for modern sets: newer equipment takes Y and C on a single 4-pin mini-DIN S-video connector. Atari-to-S-video cables join pins 1 and 5 (with ground) to that connector, plus a separate audio plug from pin 3.

5. Matching the video standard

Every Atari was built for its home market. An NTSC machine outputs 60 Hz NTSC, a PAL machine 50 Hz PAL, and a French SECAM machine SECAM. Your display, converter or capture device has to accept that standard on the input you use. Check this before you buy, especially for 50 Hz PAL or SECAM. RF adds another layer: NTSC Ataris broadcast on channel 2 or 3, PAL-B machines on channel 4 (E4), and UK PAL-I machines on UHF channel 36.

If you're stuck with RF: use the shortest, best-shielded lead you can. A plain phono-to-F adapter can beat Atari's switch box. Then set the computer's channel switch (where fitted) to a channel unused in your area and tune the TV to match. The TV must get the right signal from the switch box; a distorted picture means checking the switch-box selector and the channel match.

6. The artifact-colour catch

On an NTSC Atari, high-resolution modes (GRAPHICS 8, ANTIC mode F; also GRAPHICS 0 and ANTIC mode 3) produce artifact colours on composite and RF. Single half-colour-clock pixels turn into colours that the program never set. Programs were written to use these colours, and some software depends on them. But artifact colours are absent when using separate chroma and luma outputs. If an NTSC game looks monochrome over S-video, switch to composite for that game. PAL machines show no stable artifact colours either way, and SECAM machines none at all. The exact artifact hues also vary between NTSC models and with the TV's tint setting.

De Re Atari's quick test shows whether your connection produces artifacts. Type these lines at READY:

GRAPHICS 8
COLOR 1
POKE 710,0
PLOT 60,60
PLOT 63,60

On an NTSC machine over composite or RF, the two dots appear in different colours on the black background. Over S-video, both come out the same colour.

7. HDTV display lag

Modern TVs process the picture heavily, and the resulting delay can make an HDTV practically unusable for serious action gaming on a timing-precise machine like the Atari. The fix is the TV's game mode, which is essential if you're playing on an HDTV. Turn off motion smoothing and noise reduction too. If you use an external converter or upscaler, prefer one designed for low-latency retro use.

8. A quick setup recipe

  1. Find your model in the table in section 2.
  2. If it has chroma on pin 5, use S-video for text and general use, and keep a composite lead handy for NTSC artifact-colour games.
  3. If it lacks chroma, use composite. Use RF only as a last resort.
  4. Set the TV to the matching input and game mode.
  5. Run the Self Test's audio-visual test (hold HELP at power-on on an XL/XE) and check that the colours are steady and the sound comes through the audio lead.

Troubleshooting

  • Black-and-white picture on composite: the TV may not accept your Atari's standard, e.g. a 50 Hz PAL machine on an NTSC-only set. On S-video, an NTSC 1200XL or 800XL has no chroma signal to send.
  • Colours look wrong or drift: the 1200XL (VR1), 65XE and 130XE (R38) have colour-frequency trimmers reachable through a hole in the case bottom.
  • No sound on a monitor: the Atari's audio comes from pin 3, so connect it to the monitor's or TV's audio input. The 400/800 also produce keyclicks through an internal speaker.
  • Rolling or unstable picture: try composite instead of RF, check that the display accepts your machine's standard (50 Hz PAL vs 60 Hz NTSC), or try a different converter.
  • Controls feel sluggish: that's display lag. Enable game mode.

Further reading

  • De Re Atari, Appendix D, "Television Artifacts" — https://www.atariarchives.org/dere/chaptD.php
  • The FAQ's §6.1 for 80-column and video upgrades such as the XEP80, XEP80-II and VBXE.
  • Related guides on this site: NTSC artifacting (programming the effect), Hardware care and maintenance, Buying a used Atari today.

Credits