XL Color Boost (800XL Chroma Mod)
- Year
- 1986
- Type
- DIY project
- Category
- Video output modification
- Manufacturer
- Homebrew design by Jon Krahmer (published in Antic)
Overview
Owners of the Atari 800 enjoyed separate luminance and chrominance outputs on its monitor jack. That is essentially what later became known as S-video, and it gives a far cleaner picture than composite. Many 800XLs came with that socket only half wired. Jon Krahmer, an electronics consultant from Vista, California, noticed what he called "color smear". In Donkey Kong the blue snapper jaws had a blue smear on the right edge and a green tinge on the left. A better monitor didn't cure it, so he concluded the problem was in the computer.
Atari wouldn't release 800XL schematics (they were confidential at the time), so he spent a week tracing the board with a voltmeter and oscilloscope. His fix, "XL Color Boost", ran in Antic, Vol. 5 No. 7 (November 1986). Antic's staff tried it and judged that it gave a "more vibrant and intense" colour display, much closer to the old 800's.
What's going on
The XL's rear monitor socket is a 5-pin DIN. On paper it should carry ground, audio, composite video, luminance and chrominance. Krahmer found that his 800XL actually supplied ground, audio, full composite video, and a luminance-only signal, with one pin unconnected. The chroma signal existed on the board but never reached the socket.
The pinout of later machines confirms the pattern. Pin 5 carries composite chrominance on most models, but it is not connected on the 1200XL, NTSC 800XLs and earlier PAL 800XLs. Pin 1 carries luminance (except on the PAL 600XL), and pin 4 composite video.
The mod
Parts: one 0.01 µF ceramic disc capacitor (under $1 in 1986) and about 6 inches of thin insulated wire.
- Remove the six screws underneath, lift the keyboard half about three inches, and unplug the keyboard ribbon by its edges.
- Remove the two screws holding the board in the lower shell, lift it out, and take off the metal shields.
- Solder one end of the wire to Point B, the empty monitor-jack pin.
- Cut the capacitor leads to about 1/8 inch. Solder one lead to Point A, the chroma point by R64/R97 labelled on the main board. Solder the other lead to the free end of the wire.
- Wrap the joint in electrical tape and route the wire so the shield screws don't pinch it. Reassemble.
The capacitor passes the high-frequency colour carrier to the socket while blocking any DC level on the chroma line.
Using it
You need a display with separate luma and chroma inputs. In the 1980s that meant certain Commodore, NEC and Hitachi monitors. Today it means any TV or capture device with S-video input, using a DIN-5 to S-video cable that takes luma from pin 1 and chroma from pin 5. Krahmer stressed it won't help with a TV on the RF output.
Notes
- The article was tested only on the 800XL. The editors warned that the 130XE, 600XL and 1200XL boards differ, so verify the R64/R97 location on your board before soldering.
- Later 800XLs and most XEs already wire chroma to pin 5. Check with a meter first.
- Some XE machines have a different video problem, weak sync on the composite output, which has its own fix (see GTIA modes and video fix for late XEs).
Credits
- Picture: Antic's Figure 1: the single wire and capacitor of XL Color Boost on an 800XL board (Nov 1986). — Figure 1 from 'XL Color Boost' by Jon Krahmer, Antic Vol. 5 No. 7 (Nov 1986), via atarimagazines.com (used for identification/commentary)
- Jon Krahmer — XL Color Boost, Antic v5n7 (November 1986) — Figure 1 from 'XL Color Boost' by Jon Krahmer, Antic Vol. 5 No. 7 (Nov 1986), via atarimagazines.com (used for identification/commentary), 1986
- comp.sys.atari.8bit FAQ, section 1.15 (monitor port pinout) (Michael Current, Feb 2026) — Michael Current (comp.sys.atari.8bit FAQ), 2026
