XEP80-II
- Year
- 2021
- Type
- Modern device
- Category
- 80-column video interface (XEP80 reimplementation)
- Manufacturer
- Michael St. Pierre (MyTek); assembled units and kits from The Brewing Academy
- Tags
- modern, 80-column, xep80, ns405, hdmi, joystick-port, mytek, altirra, text-display
Overview
Atari's XEP80 gave XL/XE computers an 80-column text screen through a joystick port, but it was rare, and its picture was badly overscanned. That was tolerable on an 1980s monitor and not on a modern LCD. The XEP80-II, designed by Michael St. Pierre (MyTek) and released in 2021, is a modern reinvention. It keeps the original's National NS405 terminal-management chip and its two-wire serial link through a joystick port, so existing XEP80 software works. It adds new display timing by Avery Lee (Altirra's author) that removes the overscan, a built-in video switch between the Atari's own picture and the 80-column picture, and an optional AV-to-HDMI daughter board.
Specifications
| Item | Value |
|---|---|
| Designer | Michael St. Pierre (MyTek), 2021 |
| Controller | National NS405 TMP (48-pin) |
| Display | 80 × 24 text, 640 × 240, 15 kHz composite (CVBS); NTSC (PAL needs a separate driver and timing) |
| Memory | 64 Kbit screen RAM; OS ROM and character ROM on 64 Kbit AT28C64B EEPROMs (27C64 EPROMs also work) with two OS banks (A/B switch) |
| Link to Atari | Bit-banged two-wire serial on joystick port I/O, as on the original |
| Video switch | MAX4619 analogue switch selects Atari video or 80-column video, by push button or automatically via joystick port 2 signals |
| HDMI | Optional WiiStar WS-Z51 AV-to-HDMI daughter board (S-Video mini-DIN version), Micro-USB powered |
| Board | 4-layer, 4.5 × 4.5 inches |
| Not included | The original's 320 × 200 graphics mode and its parallel printer port |
| Availability | Assembled units and a DIY kit (PCB, tested NS405, pre-fitted socket) from The Brewing Academy; Gerbers, BOM and schematic published |
How it works
Like the original, the XEP80-II is a separate little computer. The NS405 holds the 80-column screen in its own RAM and generates the video. The Atari sends it characters and commands one bit at a time over two joystick-port lines, so no Atari RAM is used for the screen. A driver loaded on the Atari redirects the E: (screen editor) device to the XEP80, so any program that prints through E: appears in 80 columns. Software written specifically for the XEP80, such as AtariWriter 80, drives it directly.
The XEP80-II's boot disks use Avery Lee's Altirra XEP80 "Ultra Speed" driver, which runs the link much faster than Atari's original handler and adds a 40/80-column toggle. The built-in switch can flip the monitor between the normal Atari picture and the 80-column one automatically, so one screen serves both.
Software
The support package includes:
- boot disks and drivers based on the Altirra Ultra driver;
- AtariWriter 80, with its quick-reference guide and dictionary disk;
- TurboWord 80 (unmodified; needs Atari BASIC);
- demos such as DEMO80, DEMOWIN and a horizontal scrolling demo;
- customised NTSC OS and character ROM images.
Other programs that use E: work as well. Users have run FastBasic's full-screen editor in 80 columns with it.
Using it today
- HDMI. Use the recommended S-Video version of the WiiStar converter. Similar-looking boards with a barrel power jack are a different design and won't fit. Some HDTVs without native 1080p may crop the edges of the text.
- Text only. Software that uses the original XEP80's bitmap graphics mode won't display correctly.
- No printer port. The original's parallel port was left out because few drivers supported it, and dropping it frees memory. Use a separate printer interface.
- Case. A 3D-printable case (with heat-set inserts) is published for the board.
- Emulation. Altirra's XEP80 emulation and its Ultra driver are the reference for this hardware, and good for testing software first.
Compatibility
Works on Atari XL/XE computers, in the joystick port the driver expects. It's compatible with software written for the Atari XEP80's text mode and with programs that use E: once the driver is loaded.
Credits
- Picture: The XEP80-II board in its 3D-printed case, with the A/B ROM switch and 40/80 button on the front. — Image from Michael St. Pierre's (MyTek) XEP80-II page (ataribits.weebly.com) (Used for identification; copyright Michael St. Pierre)
- ataribits (Michael St. Pierre / MyTek): XEP80-II — XEP80-II overview image from MyTek's AtariBits XEP80-II page (product sold assembled and as a kit by The Brewing Academy) (used for identification/commentary)
- comp.sys.atari.8bit FAQ (Michael Current), section 6.1.2 (XEP80-II) — Michael Current (comp.sys.atari.8bit FAQ)
- AtariAge: 'FastBasic 4.5 - 2021 release' (XEP80-II with Avery's Ultra driver) and 'attempt at recreating the XEP80' — AtariAge forum members, 2021
- Altirra release notes (ALTXEP8U.SYS ultra-speed XEP80 driver) — Screenshot from Avery Lee's Altirra page, virtualdub.org
