AntiX ANTIC Switch

Year
2018
Type
Modern device
Category
Dual-ANTIC PAL/NTSC switch board
Manufacturer
Andre (A.J.) Huijts, 'Level42' (the Netherlands); ABBUC Hardware Contest 2018 entry
A blue AntiX circuit board in an Atari's ANTIC socket, carrying two stacked 40-pin chips marked C021697 and C021698, with two LEDs and the text 'Idea, design and lay-out by A.J. Huijts (Level42) 2017 The Netherlands'

Overview

ANTIC sets the Atari's screen timing: how many scan lines there are, how often the frame repeats and therefore how fast many games run. For years enthusiasts swapped a PAL machine's ANTIC for an NTSC one, or the other way round, to make a "hybrid" computer. That works, but the change is permanent, and you need a second machine to get the original behaviour back.

AntiX, short for "ANTIC switch", puts both chips in one machine. It's a small PCB that plugs into the ANTIC socket and carries two ANTIC sockets of its own, labelled Position 1 and Position 2, plus a three-pin header for a switch. The board is marked "Idea, design and lay-out by A.J. Huijts (Level42), © 2017 The Netherlands". It was entered in the ABBUC Hardware Contest 2018 and introduced on AtariAge as "AntiX, the ANTIC switch".

The designer is clear about what it does and doesn't do. AntiX doesn't produce a perfect signal for the other TV system. It gives exactly the same output as permanently swapping the chip, with the bonus that you can always go back to the factory set-up.

What you gain

Owner Benefit
PAL owners using the NTSC ANTIC Games written for American machines run at their intended speed and timing, so titles like Donkey Kong and Ms. Pac-Man feel smoother. The picture is no longer squashed vertically, and the frame rate rises from 50 Hz to 60 Hz ("PAL-60"), which flickers less on a CRT
NTSC owners using the PAL ANTIC Later demos and games written in Europe, which often break or look wrong on NTSC timing, display properly

How it works

A switching chip on the board routes about ten signals either to ANTIC 1 or to ANTIC 2. Two more switch sections hold the inactive ANTIC asleep and drive the two LEDs that show which chip is active. The switch is designed so both chips are never connected at the same moment. Switching with the power on will almost always crash the Atari, because the change isn't synchronised to the video, but it can't damage anything. The designer tested this many times. The normal practice is to switch with the power off.

Installation

  • Socketed ANTIC (most 400/800s and most XLs): no soldering. Move the original ANTIC to Position 1, fit the other-standard ANTIC in Position 2, plug AntiX into the empty socket and connect an SPDT switch.
  • Machines with a soldered ANTIC (typically XEs): desolder ANTIC and fit a socket first.
  • 400/800: needs a ribbon extension cable and adapter, because ANTIC sits on the CPU board inside the shielding.
  • Wiring the switch: the header pins marked +5V and GND are signal levels, not supply connections. Connect only the switch's two outer pins to the outer header pins and its centre pin to the centre pin. AntiX takes its power from the ANTIC socket.

Getting a picture

  • PAL machines are the easy case. Almost all TVs made since the mid-1990s accept PAL-60 through composite or S-Video, so AntiX alone is enough.
  • NTSC machines in PAL mode output a PAL-M-style colour signal that few American TVs handle. You need a PAL-M capable set or a professional monitor such as a Sony PVM. A permanent ANTIC swap has the same problem.
  • With Sophia: the designer recommends pairing AntiX with the Sophia video upgrade, which replaces the colour encoding with RGB, component (YPbPr) or DVI output. Then either ANTIC gives a clean colour picture on any suitable display. It also lets a PAL owner use a Philips CM8833 or Commodore 1084 over RGB at NTSC speed.

Related

Credits