Micro Mainframe MF-1681 Disk Drive

Year
1983
Type
Storage
Category
5.25-inch floppy disk drive with Z80 controller (third-party)
Manufacturer
Micro Mainframe, Rancho Cordova, California
Black-and-white photo of a light-coloured drive cabinet with two half-height drive bays

Overview

The MF-1681 came from Micro Mainframe of Rancho Cordova, California. In 1983 the company said it had been "the largest manufacturer of peripherals for the TRS-80 line" for four years, and the MF-1681 was its move into the Atari market. Instead of the 6507 found in Atari's drives, it uses a 4 MHz Z80A with 16 KB of RAM. That made it a small computer in its own right. It recognises single and double density automatically, has a Centronics printer port with a 4 KB print spooler, and comes in a wide cabinet with room for a second half-height drive. Micro Mainframe's firmware also anticipated far more: hard disks, disks of up to 2,097,150 sectors, and running CP/M, OASIS or TRSDOS on the drive's own Z80. Those extras never shipped.

Specifications

Item Value
Maker Micro Mainframe, Rancho Cordova, California
Year 1983 (Antic review September 1983)
Price $549.95 base unit; $249.95-$300 for a second drive
Controller Z80A at 4 MHz, 16 KB RAM, WD1797 floppy controller
Formats Single-sided, single and double density (180 KB DD), automatic density recognition
Mechanisms TEC (Tokyo Electronic Corporation, as Antic gave the name) half-height 5.25-inch drives
Size 16.5 × 7.5 × 5 inches, about three inches longer than an 810
Expansion Second internal drive; 34-pin edge connector for up to 3 more drive units, up to 8 drives total, 5.25- or 8-inch, single- or double-sided
Printer Centronics parallel port, 4 KB spooler (38 KB with the 64 KB RAM upgrade)
Speed Up to 76.8 kbit/s possible in the firmware, but no DOS supported it
Software Utility disk (SETDBL, PRTTRK, PRTSEC, ADUP, DISASS); no DOS included

History

Antic's Larry Dziegielewski reviewed the drive in September 1983. He was impressed by the quiet, smooth TEC half-height mechanisms. They also stopped spinning after about three seconds, where an 810 runs on for seven. He liked the automatic density recognition, which let him swap single- and double-density disks without special commands, and the power of the Z80, which could read, write and print whole tracks from BASIC. His unit worked "flawlessly for two months". At $549.95, plus about $300 for a second drive, he reckoned a dual double-density system came in under $850, "a bargain compared to the PERCOM and ATARI drives".

Micro Mainframe planned an expansion box that would turn the drive into a 64 KB Z80 machine running CP/M, TRSDOS, OASIS and a "MAXIDOS", plus a hard disk host adapter. Upgrade options were defined as model numbers: MF-1682 (second drive), MF-6481 (64 KB RAM) and MF-6482 (both). The promised "Maxi-DOS A" never appeared, so buyers used existing DOSes instead.

Using it today

  • DOS. The drive works with Atari DOS 2.0S, OS/A+ version 4 and MyDOS. The bundled SETDBL utility can build a bootable double-density "DOS 2.0M" from a DOS 2.0S disk.
  • Utilities. PRTTRK and PRTSEC print any track or sector, ADUP backs up disks, and DISASS is a 6502 disassembler.
  • Extra drives. Up to three external units can be connected to the edge connector, including 8-inch drives with an adapter cable. Double-sided drives use a track-first (interleaved) layout.
  • No high speed in practice. The firmware can do 76.8 kbit/s, but no DOS ever supported it, so treat the drive as a standard-speed device.

Compatibility

Reads and writes Atari single-density disks and double-density disks for DOSes such as OS/A+ 4 and MyDOS. It doesn't support 1050 enhanced density. Works with any Atari 400/800/1200XL (and later XL/XE) through SIO.

Credits