Amdek AMDC-II 3-inch Disk Drive
- Type
- Storage
- Category
- 3-inch floppy disk drive (third-party)
- Manufacturer
- Amdek Corporation (Elk Grove, Illinois)
Overview
Most Atari drives used 5.25-inch floppies. Amdek, better known for its monitors and plotters, went another way with the AMDC-II: a twin drive using the 3-inch Compact Floppy format, the hard-shelled, two-sided ("flippy") cartridge disk of the early 1980s. Nothing else for the Atari used that form factor. A single-drive AMDC-I was planned but never released.
Specifications
| Item | Value |
|---|---|
| Media | 3-inch Compact Floppy (two-sided, used one side at a time) |
| Drives | Two, single-sided (AMDC-II) |
| Densities | Single (810), enhanced (1050) or double (Percom-style); ED or DD chosen by a hardware switch |
| Interface | Atari SIO, plus a DA-15 parallel printer port |
| Firmware extras | Memory read/write/execute, high-speed sector commands, custom format interleave, drive-ID remapping |
| Bundled software | Early units: DD DOS Disk Builder (AMDEKP.BLD) to make a double-density DOS 2.1A from DOS 2.0S; later units: DOS XL |
How it works
The drive has some notable quirks.
- The density switch. The drive can't detect both enhanced and double density automatically. The "1050 compatibility" switch decides which one it recognises.
- Enhanced density shortfall. In enhanced mode the firmware reports 1,024 total sectors rather than the 1,040 a 1050 disk has, apparently to suit DOS 2.5. The format command still lays down all 1,040, and the extra 16 can be reached by rewriting the Percom block.
- Extended commands.
$72/$77/$70are high-speed read/write/put. Only the data frame runs at the higher rate, and that rate is set in hardware.$74-$76force medium, single or double density.$66sets a custom interleave for the next format, and it clashes with the US Doubler's command of the same number.$63/$64read and set the IDs of up to four mechanisms.$43checks the density of an inserted disk.$78re-initialises the drive. Memory read, write and execute commands ($58-$5A) exist but are enabled only by an internal jumper and particular switch settings.
The AMDC-II also carries a parallel printer port and a second SIO port for daisy-chaining.
Using one today
- Getting 3-inch media is the main hurdle. The cartridges are two-sided, so each disk holds two Atari "sides" written separately.
- Because of the
$66conflict, software that uses the US Doubler's skewed-format command can misbehave on an Amdek. Use the Amdek's own DOS or generic formatters. - Supplies were already scarce in the 1980s. In October 1986 an Antic reader answered another's question by naming a single Indiana shop that still sold Amdek 3-inch drive hardware and software.
Compatibility
Software sees it as a Percom-style drive with the enhanced-density caveat above. Disks written in single or double density can be copied to 5.25-inch media and imaged as normal ATRs. Compact Floppy disks themselves can only be read in Amdek or other 3-inch hardware.
Credits
- Picture: A 3-inch Compact Floppy disk, the media used by the Amdek AMDC-II. — Blake Patterson, via Wikimedia Commons (CC BY 2.0)
- comp.sys.atari.8bit FAQ (Michael Current), sections 3.2.5 and 4.6 — Michael Current (comp.sys.atari.8bit FAQ)
- Altirra Hardware Reference Manual, section 10.32 Amdek AMDC-I/II — Avery Lee (Altirra)
- Antic Vol. 5 No. 6 (October 1986), I/O Board: Amdek Shopping — AtariMagazines.com (Kevin Savetz), 1986
