Concorde C-221M Disk Drive
- Year
- 1984
- Type
- Storage
- Category
- 5.25-inch floppy disk drive, master/slave (third-party)
- Manufacturer
- Concorde Peripheral Systems, Inc., Laguna Hills, California
- Tags
- disk-drive, master-slave, z8, concorde, double-density, dos-xl, third-party, 1984
Overview
The Concorde C-221M was a low-priced Atari-compatible floppy drive from Concorde Peripheral Systems of Laguna Hills, California, announced in ANALOG Computing's October 1984 issue. Its selling point was a master/slave arrangement. One C-221M master held the controller and the SIO connection, and up to three cheaper C-221S slave drives, with mechanisms but no controller, plugged into a 34-pin connector on its board. A full set of four single-sided drives gave 704 KB online. Concorde also announced double-sided C-222M/C-222S models, which probably never shipped.
Specifications
| Item | Value |
|---|---|
| Maker | Concorde Peripheral Systems, 23152 Verdugo Drive, Laguna Hills, California |
| Announced | 1984 (ANALOG Computing #23, October 1984) |
| Prices (1984) | C-221M master $369; C-221S slave $269; C-222M $459; C-222S $349 |
| Capacity | 88 KB single density, 176 KB double density per disk (single-sided) |
| Controller | Zilog Z8681 microcontroller at 7.3728 MHz, 2 KB ROM, 1 KB RAM, WD2797 floppy controller |
| SIO | One SIO port only, so it must be at the end of the chain; serial via the Z8's hardware UART at exactly 19,200 bit/s |
| Slaves | Up to three C-221S drives via a 34-pin PCB edge connector |
| Mechanics | Direct-drive motor, optical track-zero sensing |
| Software | Shipped with DOS XL; ANALOG's announcement mentions Atari DOS |
| Warranty | One year, over-the-counter exchange; 48-hour factory test |
How it works
Most Atari drives of the day ran a 6502-family or Z80 processor and generated the serial signal in software ("bit-banging"). The Concorde uses a Zilog Z8 microcontroller (the ROMless Z8681) clocked at 7.3728 MHz, a standard UART crystal frequency, and sends serial data through the Z8's built-in UART. As a result its transmit rate is exactly 19,200 bit/s rather than the slightly fast rate of software-timed drives. There's no high-speed SIO mode.
The drive has only a single SIO connector, unlike the two found on Atari's and most third-party drives, so it has to be the last device on the SIO chain. The slave drives hang off the master's internal drive cable through a 34-pin edge connector, a design similar to Trak's AT-series drives.
ANALOG described the C-221M as storing 88 KB in single and 176 KB in double density. Analysis of firmware version 1.2, however, shows only single-density support, so double density may depend on the firmware version fitted.
Using it today
C-221M drives are rare. If you find one:
- Put it last on the SIO chain, since there's no pass-through port.
- Check density support with the DOS you plan to use. Start with single density, which every firmware version handles.
- Slaves need a master. A C-221S on its own has no controller and won't work alone.
- Treat it as a standard-speed drive. No high-speed DOS supports it.
Compatibility
Works with Atari 400/800/XL/XE computers through SIO. It reads and writes standard 810 single-density disks, and double density with suitable firmware and DOS (DOS XL was shipped with it). It doesn't handle 1050 enhanced density.
Credits
- ANALOG Computing #23 (October 1984), New products: New Atari drive (Concorde C-221M), Internet Archive — Internet Archive, 1984
- comp.sys.atari.8bit FAQ (Michael Current), sections 3.2.5 and 3.2.7 (Concorde C-221M/C-222M) — Michael Current (comp.sys.atari.8bit FAQ)
- Altirra Hardware Reference Manual (Avery Lee), drive characteristics and transmit timing tables (Concorde C-221M v1.2) — Avery Lee (Altirra)
