Percom RFD and AT-88 Disk Drives

Year
1982
Type
Storage
Category
5.25-inch floppy disk drives (third-party)
Manufacturer
Percom Data Company / Percom Data Corporation (Dallas, Texas)
Front of a Percom RFD40-S2 dual disk drive

Overview

Percom Data of Dallas sold the first disk drive for the Atari that didn't come from Atari. The RFD40-S1 was introduced in March 1982 and offered something the Atari 810 couldn't: double density, 256-byte sectors and about 180 KB per side. To let software discover and change a drive's format, Percom defined a 12-byte configuration record that the computer could read and write over SIO. That record, the Percom block, became the standard way for almost every later Atari drive (except Atari's own 810 and 1050) to report single or double density.

Percom produced two related families: the RFD line (single and dual, single- and double-sided) and the cheaper AT-88 line, which started as single density only but could be upgraded.

Specifications

Model Format Notes
RFD40-S1 SS SD/DD March 1982; first 810 alternative
RFD44-S1 DS SD/DD 1982; early double-sided format left the last 4 sectors unusable
RFD40-S2 / RFD44-S2 Dual drives, SS or DS 1982 / 1983
AT88-S1 / AT88-S2 SS SD (single / dual) 1983; double density via the AT-88 Doubler upgrade
AT88-SPD (S1PD) SS SD/DD Adds a built-in parallel printer port and second SIO port
Common item Value
Controller CPU Motorola 6809 (1 MHz in the AT-88)
Firmware 2 KB ROM (RFD, AT-88); 4 KB in the SPD, for the printer code
Expansion Controller drive runs up to three add-on (slave) drives
SIO rate 19,200 bit/s
AT-88 SD capacity 88,000 bytes per side (manual figure), 48 tpi
Head seek 20 ms track-to-track
Bundled software Percom DOS 2.0P builder (early), OS/A+ version 2 or 4, later DOS XL

History

The early RFD drives came with a "BLD" utility that built a double-density Percom DOS 2.0P from your own copy of Atari DOS 2.0S. Later units shipped with OSS's OS/A+ version 4. The AT-88 was a later, cost-reduced design that wasn't compatible with the RFD. Its owner's manual is dated 1982, and it shipped with OS/A+ 2.00. It works with a 400 or 800, and it can be set up in twelve configurations, from a single controller drive up to a controller with three add-ons alongside an Atari 810.

In November 1983 Antic reviewed the AT-88 S-1 at $488 for the first drive. Richard DeVore pointed out that this was more than $100 below the 810, and the drive used about half the 810's shelf space. He praised the manual as one of the best he had seen and reported that every program he tested loaded correctly. By mid-1985 Antic's guide to DOS versions listed Percom among the brands (with Rana, Indus, Trak and Astra) whose owners "already enjoy" true double density, which no Atari-made drive offered at that point.

The Percom configuration block

The block is 12 bytes, read with SIO command $4E ("N") and written with $4F ("O"). It holds the tracks per side, step rate, sectors per track, number of sides, FM or MFM recording, bytes per sector, and a translation-control byte. Because the computer can set density on the fly, owners can swap single- and double-density disks freely. Support among other manufacturers varied. The Indus GT, for example, honours only bytes 5-7, and the Atari XF551 implements part of the block.

Known issues

Four RFD firmware revisions are known (V1.00, V1.10, V1.20, V2.10), each with its own bugs: - V1.00 doesn't report deleted-sector marks as errors, which breaks some copy-protected disks. V1.10 fixes this. - Before V1.20, side-2 sectors could wrongly be forced to 128 bytes in double density. - Before V2.10, density detection worked only on D1: and formatted sectors were filled with non-zero data. - Every revision has an off-by-one error mapping side-2 sectors, so the last logical sector lands on track 0.

Astra's 1001 and 1620 use a near-identical copy of the RFD V1.10 firmware, differing only in the default step rate.

Using one today

  • Single-sided double-density disks from a Percom are the standard 180 KB format that SpartaDOS, MyDOS and DOS XL all understand, and image tools treat them as normal 256-byte-sector ATRs.
  • Double-sided RFD44 disks use Percom's own side-2 layout. Early units also lose the last four sectors. Don't expect them to read in an XF551 or another brand's double-sided drive.
  • Altirra's release notes record emulation of the Percom AT-88 (with a choice of 1791 or 1795 FDC) and the AT88-SPD, and its hardware manual documents the RFD firmware in detail. That's useful for testing how software behaves on these drives.

Credits