Atari 850 Interface Module Service Manual
- Year
- 1981
- Type
- Component
- Category
- Atari service documentation: how the 850 boots, its three power rails, clock, RAM self-check and port tests
- Manufacturer
- Atari, Inc.
- Tags
- 850-interface, rs-232, service, repair, field-service-manual, 6507, 6532, boot, r-handler, troubleshooting, 400-800, atari-inc
- Related
- Atari 850 Interface Module, Atari 820 Printer Service Manual, Atari 1020 and 1027 Printer Field Service Manuals, Atari 400 Troubleshooting (Sams Computerfacts CC5 and the Sears Repair Manual), Atari 410 and 1010 Program Recorder Service Manuals, Atari 800 Troubleshooting (Sams Computerfacts CC7)
Overview
The Atari 850 Interface Module gave the 400 and 800 four RS-232 ports and a parallel printer port. Atari's 850 Interface Module Service Manual is publication CS 400/800-S004. The copy that survives is Revision B, dated April 1981, with a 1982 copyright page. It is unusually readable. Its first two chapters explain how the module works and how it boots. The third covers handling, disassembly, preventive maintenance and a troubleshooting guide split into "it boots" and "it doesn't boot". Appendices cover the power supply, clock circuit, 6532 chips, SIO protocol, revision levels, a port-test program, parts lists and pinouts. This page summarises the parts that matter to anyone repairing an 850 today. Atari's separate 850 Technical Manual (1982) is a programming reference for the R: device and isn't covered here.
Inside the 850
- CPU. A 6507 (the 6502 cut down to 13 address lines, so an 8K address space) runs a 4K ROM, Atari part C012099. The ROM's revision is the suffix: "C012099-03" means Revision 3. You can read it through a sliding window in the RF shield. The board revision is printed on the solder side.
- I/O. Two 6532 chips, which the manual calls PIAs and also RIOTs, each provide two 8-bit ports, 128 bytes of RAM and a timer. Their combined 256 bytes are the 850's only RAM and serve as its data buffer. Eleven of their 32 I/O lines drive the printer port: eight data bits, strobe, busy, and a "printer connected" line.
- Ports. Port 1 has the fullest RS-232 signal set. Ports 2 and 3 have data plus two handshake lines each. Port 4 can drive a 20 mA current-loop teletype. Buffers between the chips and the connectors protect the expensive LSI parts.
- Power. The 9 V AC adaptor feeds three rails: 5 V for the logic, and 10 V and −8 V, which are used only by the serial-port output buffers and, for the 10 V rail, the clock.
How it boots
The manual's account of start-up explains why the order matters: switch the 850 on before the computer. While the computer is off, the 850's power-on reset holds the 6507 and both 6532s in reset. When the computer's Vcc/READY line (SIO pin 10) goes high, the reset is released and the 850 starts watching the COMMAND line.
At power-on the computer sends a status request to disk drive 1, repeating it 28 times if nothing answers. If no drive 1 is present, the 850 answers on the 27th request, posing as drive 1 at device ID $31. It then downloads its serial-port handler into the computer. After that it responds only to its own IDs: $40 for the printer port and $50–$53 for the serial ports. If a real drive 1 answers, DOS loads instead, and later DOS versions fetch the 850 handler themselves. Command frames arrive at 19,200 baud.
Troubleshooting, the Atari way
If it boots, the 5 V supply, clock, reset, CPU, part of the ROM and the SIO buffers are known to work. Remaining faults are usually:
- The 10 V or −8 V rails. Check them against ±5%. A low rail can leave some peripherals working and others failing, or cause intermittent errors. If the 10 V regulator (A113) runs hot and the rail is low, pull the port buffer chips A105 and A106 one at a time to find the one loading it.
- Local RAM. The RAM test result is sent, unannounced, to the printer port. $00 means a pass. $AA means a fault in A104 and $2A a fault in A103. No strobe is sent, so a printer usually won't show it, but a scope on printer-port data pins 3, 5 or 7 will.
- A dead serial port. Run Appendix 7's BASIC port test with pins 3 and 4 of the port linked as a loopback. If errors appear only at higher baud rates, the buffer is out of spec. Replace A105–A108 for the serial ports, or A110/A111 for the printer port. Because output uses the 10 V and −8 V rails and input doesn't, output-only faults point back to the supply.
If it doesn't boot, check in this order:
- 5 V at the test points: 4.75–5.25 V with less than 0.1 V of ripple. Check that regulator A112's heat sink is firmly attached.
- The clock at Z102 pin 13, about 1 MHz. A clean wave at pin 13 but a weak one at pin 12 means something is loading it, often the 6507 (A101). The frequency must be 1.1084045 MHz (902 ns per cycle), or serial timing errors stop the boot. Below about 7 V the clock flip-flop stops following its input, and then crystal X101 is suspect.
- Power-on reset: confirm that Vcc/READY actually arrives from the computer.
- Then the CPU, ROM and SIO buffers, and finally broken or shorted address lines (Appendix 9). The manual blames these on board warping or "crystal growth since manufacture".
Opening it up
Four screws in the base hold the shell together. Lift the top off and the board is exposed for voltage checks. To lift the board out of the base, free the serial-port edge first. When refitting it, put the switch and LED edge in first. The RF shield's two halves are held by twisted tabs through the board. Atari asked technicians not to remove the serial-number sticker, and to keep plastics, including mylar sheet protectors, away from the board because of static.
Related
For terminal use and the R: handler see 850 Express!-era modems and the P:R: Connection, a smaller alternative to the 850.
Credits
- Picture: Cover of Atari's 850 Interface Module Service Manual. — Cover of the Atari 850 Interface Module Service Manual (Atari, Inc., 1981-82), scan from the Internet Archive (Fair use (cover of a service manual))
- Internet Archive item Atari850InterfaceModuleFieldServiceManual (OCR text) — Cover of the Atari 850 Interface Module Service Manual (Atari, Inc., 1981-82), scan from the Internet Archive (Fair use (cover of a service manual))
- Atari 850 Interface Module Technical Manual (1982) (Internet Archive, OCR text) — checked for scope only — Internet Archive, 1982
