Top Drive 1050 (Polish 1050 Turbo clone)
- Year
- 1987
- Type
- DIY project
- Category
- Disk drive ROM upgrade
- Manufacturer
- Ataserw (Poland); module shown built by Zenon/Dial
- Tags
- diy, atari-1050, turbodrive, 1050-turbo, poland, ataserw, eprom, 27128, drive-upgrade, intermediate
Overview
Top Drive 1050 is a Polish upgrade for the Atari 1050 disk drive, made by Ataserw of Tychy in 1987 or 1988. It is a clone of Bernhard Engl's German 1050 Turbo. Its ROM, credited to P.Z. Karen, a brand of LDW, replaces the drive's firmware and adds Engl's Turbodrive high-speed protocol, about 68,200 bit/s and advertised as "70,000 baud". Like the original, it has no extra CPU or RAM buffer: speed comes from the firmware and optimised sector layouts. The upgrade was supported by Ataserw's TURBO DOS ("TUR-DOS"), known as version 2.5 (1989, probably on disk) and rev. 4.0 (1990, on cartridge).
Top Drive belongs to the same Polish tradition as the TOMS drive turbos and the cassette turbo systems. An upgrade project also exists that converts a Top Drive to be compatible with the Happy 1050 Enhancement.
The module
In 2001 Krzysztof Paizert sent the collector Nir Dary a Top Drive module built by Zenon/Dial, with Polish assembly notes that Paizert translated. The photos show a small stripboard carrying:
- an AM27128 EPROM in place of the 2764 the design expects. Zenon didn't have a 2764, so he burned the same program into both halves of the 27128.
- an SN74LS74 flip-flop and an SN74LS00 NAND gate, plus a few passive parts
- two rows of header pins that plug into the drive's ROM socket
- a two-wire lead (blue and yellow) to points on the drive board.
The disk that came with it held TRACKOPY (a copier), B88.INI and INITGL.COM (initialisers) and TURBOON (a program that switches turbo on).
Installation (from Zenon/Dial's notes)
- Open the 1050 and remove the ROM chip U10 from its socket.
- Plug the Top Drive module into the ROM socket. Zenon fits an extra socket onto the module's pins and plugs that into the original socket.
- Connect the blue wire to the test pin near potentiometer TP10, and the yellow wire to resistor R66, near VR2 and CR22 on his drawing.
- Jumpers JP1–JP7: re-solder them as shown on the diagram if the drive originally had a mask ROM. If it already had an EPROM, leave the jumpers alone.
- Reassemble the drive.
Using it
- Switch the drive on with the door lever raised, then switch on the computer. The Top Drive menu loads from the drive's ROM.
- Insert a disk and press START or SELECT as the menu offers.
- A BOOT ERROR message appears during this step. Zenon notes that this is normal.
- As with Engl's original, disks need to be formatted in the Turbo layout for full speed. The QMEG+OS operating system detects 1050 Turbo-type drives and uses their fast mode.
Notes for builders
- Copies of Zenon's photos, the assembly text and a Top Drive ATR are in the Nir Dary CD collection on
ftp.pigwa.net, under Hardware Projects/Top Drive. - As of February 2026 the Polish shop Galtron was listed as a source of new Top Drive boards.
Credits
- Picture: A hand-built Top Drive 1050 module by Zenon/Dial (2001): a 27128 EPROM and two TTL chips on stripboard. — Photo of Zenon/Dial's Top Drive 1050 module, Nir Dary CD collection (ftp.pigwa.net)
- Krzysztof Paizert / Zenon/Dial — TOP DRIVE 1050 assembly description (e-mail of 17 August 2001), Nir Dary collection — Photo of Zenon/Dial's Top Drive 1050 module, Nir Dary CD collection (ftp.pigwa.net), 2001
- Top Drive diskinfo.txt (disk contents)
- Photos 'Top 1050 Front.jpg' and wiring drawing '1.JPG' (Nir Dary collection) — Photo of Zenon/Dial's Top Drive 1050 module, Nir Dary CD collection (ftp.pigwa.net)
- comp.sys.atari.8bit FAQ, section 3.2.2 (Top Drive 1050 by Ataserw; 1050 Turbo) — Michael Current (comp.sys.atari.8bit FAQ)
- QMEG+OS 4.0 description (supported speeders include 1050 Turbo)
