1050 Duplicator (Duplicating Technologies)

Year
1986
Type
Upgrade
Category
Disk drive upgrade (Atari 1050 copier and double-density board)
Manufacturer
Duplicating Technologies, Inc. (DT/DTI), Jericho, New York
Green 1050 Duplicator circuit board with a 40-pin processor, support chips and an empty IC socket

Overview

The 1050 Duplicator was a 1986 upgrade board for the Atari 1050 from Duplicating Technologies, Inc. of Jericho, New York. Like the Happy 1050 it puts a full 6502 computer in the drive. The board adds its own ROM and a large RAM buffer, reads a whole track at a time, adds true double density (180 KB, Percom-compatible), and supports a high-speed SIO mode compatible with ICD's UltraSpeed. Its main selling point, though, was copying: DT shipped it with a menu-driven backup program and kept mailing out new software revisions to handle the latest copy protection.

DT also made a cheaper sister board, the Density Doubler 1050, with the same 6502, double density, track buffering and US Doubler emulation, but without the Duplicator's copy-protection tools.

Specifications

Item Value
Maker Duplicating Technologies, Inc., Jericho, New York
Released 1986
Drive CPU 6502 at 1 MHz (replaces the 1050's 6507)
Firmware ROM 4 KB used by the drive (often listed as an 8 KB chip)
Buffer RAM Track buffer for a whole track; DT's manual calls it a "4000 byte buffer", other references list 8 KB
Formats Single (90 KB), enhanced (130 KB), double (180 KB, 256-byte sectors)
High speed UltraSpeed-style, about 52,600 bit/s (US Doubler compatible); slightly slower in later firmware so all 1050s could keep up
Track buffering Read only, 18 sectors per track in SD or DD
Code upload Yes (custom commands for track reads and writes)
Software Duplicator copy program, RPM test, double-density DOS, Skew copier, Disk Test, Create Slo, Format Fix, protection "modules"
Upgrades 20-sector "Slow Mod" kit; Happy's CheerUp upgrade (1987) for Happy software compatibility

History

DT described the Duplicator as "really a small computer" inside the drive. The installation pack arrived with a promise of a free software upgrade within 30 days, and later disks were sold for about $5 to cover the media and postage. By version 3.0 the package filled four disk sides:

  • Side 1: the auto-booting copy program and an RPM checker.
  • Side 2: a double-density DOS plus utilities. These were a format helper, a Skew copier for track-alignment protection (DT named SSI's Mech Brigade and Nam and MicroProse's F-15 Strike Eagle as examples), a drive Disk Test, Create Slo (makes a disk that switches the Duplicator off in under a second) and Format Fix (cures error 139 when DOS 2.0S reformats a double-density disk).
  • Sides 3 and 4: custom-format modules produced by DT's in-house "Module Maker". Version 3.0 added backups of weak-sector protection, as used on Zorro and The NeverEnding Story.

Version 3.0 also brought an ultra-high-speed sector copier that could run many unprotected disks at high speed. Later versions 4 and 5 followed, and the Electronic Arts skew protection was promised for 4.0. Happy Computers sold a CheerUp upgrade in 1987 that made a Duplicator drive compatible with Happy 1050 software.

How it works

After installation, the drive reads a full track into the buffer instead of fetching one 128-byte sector at a time. DOS loads get much faster and the head moves less. The drive "knows" what's on a whole track, so copy software can analyse the track layout and recreate bad sectors, duplicate sector numbers and CRC errors on the destination disk.

Two quirks set it apart:

  • Boot sectors. Most double-density Atari drives format every sector at 256 bytes and just transfer the first three as 128 bytes. The Duplicator physically formats the boot sectors of a double-density disk as 128-byte sectors. It's the only drive known to do this. Disks made this way may not read correctly in other drives' track-level tools.
  • Fast and slow modes. Track buffering upsets some protected disks that time their own loading. The Duplicator can be "deprogrammed" from software, which makes the drive behave like a stock 1050 until it's switched off and on again. Power-up always returns the Duplicator to fast mode.

High speed. SpartaDOS automatically uses the Duplicator's UltraSpeed-compatible transfer mode. DT also supplied its own high-speed handler for its copy software. Early firmware ran at about 52,000 baud, which not every 1050 mechanism could sustain, so later versions slowed it a little.

Installation and tips

The board plugs in after you remove two chips from the 1050's main board. That means opening the case, unplugging seven connectors and lifting out the mechanism. There's no soldering, except for the optional Slow Mod.

  • Set the RPM. DT insisted on 288 RPM (60 Hz drives). Above that the drive can't write the 19-sector tracks used by "double sector" protection. Use the supplied RPM program and the VR2 trimmer on the 1050 main board.
  • 20-sector Slow Mod. A few disks, such as Questron, were written with 20 sectors per track on a slowed-down drive. DT's soldered kit let its software drop the motor to about 270 RPM for those tracks. Even DT recommended skipping it unless you needed it.
  • XE computers. DT noted that some XE machines have diodes on the SIO lines that slow high-speed transfers, and its fix was to remove them. Today, check for other causes first.
  • Atari DOS 3 was best avoided: DT warned that it has bugs and isn't true double density. SpartaDOS was the recommended DOS.

Using it today

A Duplicator-equipped 1050 still makes a capable everyday drive: double density, track-buffered reads and high-speed transfers with any DOS that supports UltraSpeed. SpartaDOS is the classic example. Altirra offers full emulation of the 1050 Duplicator (you supply the firmware image), and its hardware manual records the Duplicator's Percom block values, SIO timing and format behaviour.

When you move disks to other systems, remember the 128-byte boot-sector quirk. Disks are readable through the normal SIO commands, but low-level image tools may see a slightly unusual track.

Compatibility

  • Reads and writes 810 single-density and 1050 enhanced-density disks.
  • Double density is compatible with Percom-standard drives.
  • US Doubler compatible, so UltraSpeed-aware software works.
  • CSS's Ultra Speed and Ultra Speed Plus operating systems list it among their supported high-speed drives. The TOMS Multi Drive upgrades and the modern Mega Speedy can emulate it.

Credits