Build-Your-Own EPROM Burners

Year
1985
Type
DIY project
Category
EPROM programmer
Manufacturer
Homebrew designs (Larry Woodgeard & Charles Cherry, Antic 1985; Rudolf Cornelissen, 1999)
Magazine page headed 'assembly language' with the title 'BUILD YOUR OWN EPROM BURNER: Chip programming for $30' by Larry Woodgeard and Charles Cherry, followed by three columns of article text including 'What's an EPROM?' and 'Modes of Operation'.

Overview

Being able to burn your own EPROMs means custom OS ROMs, homemade cartridges, BASIC replacements and drive-ROM upgrades. In the 1980s a commercial programmer was expensive, so magazines and hobbyists published their own. Two well-documented Atari designs follow.

1. Antic's joystick-port burner (1985)

Antic, Vol. 4 No. 8 (December 1985, the Fourth Annual Shoppers Guide), carried "Build Your Own EPROM Burner — Chip programming for $30" by Larry Woodgeard and Charles Cherry. Its driver, EPROG, is a short machine-language program assembled at $6000 (© 1985 Antic Publishing, credited to Larry A. Woodgeard). The listing shows how the hardware works.

All I/O goes through the joystick ports. The PIA's PORTA ($D300) carries everything, and the program flips the port's direction with PACTL ($D302) to switch between output and input:

PORTA bit Use
0–3 4-bit data/address nibble
4 ($10) CLK, which clocks the nibble into latches on the board
5, 6 ($20, $40) RW1/RW2, select which data nibble is read back
7 ($80) EN, the programming pulse enable

To set an address, the program clocks out four nibbles (high to low) into on-board latches. To read, it switches the low nibble to input and reads the EPROM's data byte as two nibbles. To program, it clocks out the data byte as two nibbles plus the address, then pulses EN for a timed delay. It then moves to the next byte.

Workflow: pick a chip type, 2716, 2732 or 2764, then Read or Program. The program tells you which switches on the board to set for each chip: switch 3 up for one type, switch 2 for another, switches 1, 4 and 5 for the third, and all down to finish. You press START to continue. The 8 KB buffer runs from $7000 to $8FFF, so you load a ROM image there (for example from DOS) before programming, or save it from there after reading.

This is a modest build: a few latches and switches on perfboard, a joystick cable, and an external programming supply as described in the article. Because it uses only the joystick ports, it works on any 8-bit Atari with enough RAM for the buffer.

2. Rudolf Cornelissen's cartridge programmer (1999)

A more ambitious design for the XL. It is a cartridge that plugs into the top slot and programs 8 KB and 16 KB EPROMs. It needs no external power supply, because an on-board TL497 step-up regulator generates the programming voltage from the Atari's 5 V. It needs at least 40 KB of RAM. It was released as shareware. The package contains:

  • PGM.BAS, a BASIC front end with a machine-language core (load, save and directory routines are in BASIC);
  • the double-sided PCB layout as RUDPROG2.PCB (smARTWORK on the PC), plus RPSOLCOM.PCB and RPSOLSIL.PCB drawn on the Atari with smARTWORX. The silkscreen file lists every component value.

Builder's warnings:

  • It needs "advanced soldering skills" and a home-made double-sided board. Join the layers with short wires through the holes. If you print from the Atari layout files, lengthen the edge connector by 2.54 mm.
  • Insert EPROMs with pin 1 towards the TL497. The wrong way round can damage the EPROM, the programmer, the Atari or its power supply.
  • Two multiturn trimmers set 12.5 V (inner) and 21 V (outer) programming voltages. Measure across the 1000 µF capacitor. The software waits 30 seconds for the 21 V supply to settle, which is your window to trim it with no EPROM inserted. Never try 21 V on a 12.5 V part. If unsure, try 12.5 V first.
  • Use 2 MHz PIAs. 1.5 MHz parts may work, but aren't recommended.
  • Expect slight screen flicker from the step-up converter.
  • Run it under DOS 2.5 without the RS-232 handler. Memory from decimal 20000 up is the EPROM buffer, leaving about 3.5 KB spare.

Tips for today

  • Erase UV EPROMs fully before programming, and check blank before burning.
  • 27C-series CMOS parts usually want 12.5 V. Old NMOS 2716/2732s often need 21 V or 25 V. Read the datasheet.
  • Modern USB programmers are cheap, but these projects remain an excellent education in driving hardware from an Atari's PIA and cartridge port.

Credits