Hyper-XF (hyper+ XF) ROM for the XF551
- Year
- 1998
- Type
- DIY project
- Category
- Disk drive ROM upgrade
- Manufacturer
- Stefan Dorndorf (homebrew EPROM image)
- Tags
- diy, xf551, rom, eprom, ultraspeed, 3.5-inch, partitions, abbuc, germany, drive-upgrade
Overview
Hyper-XF, written "hyper+ XF" in its manual, is a replacement drive operating system for Atari's XF551 disk drive, released in 1998 by the German programmer Stefan Dorndorf. You burn it into an 8 KB EPROM and swap it for the drive's original ROM. No soldering is needed. It fixes many bugs in Atari's firmware and turns the XF551 into a much more flexible drive, especially when it has been converted to a 3.5-inch mechanism.
There are two builds, and you must use the right one:
| Version | For |
|---|---|
| Hyper-XF 1.0A | an original XF551 with its 5.25-inch mechanism |
| Hyper-XF 1.0B | an XF551 converted to a 3.5-inch mechanism. Dorndorf warns never to use B with a 5.25-inch drive |
What it adds
- UltraSpeed transfers. The XF551's own high-speed mode is replaced by the UltraSpeed protocol used by the Speedy 1050. The manual puts this at about 55,000 bit/s instead of 19,200. Most XL/XE OS extensions (QMEG-OS, SpartaDOS and others) and many DOS versions already support UltraSpeed. As with the stock XF551, disks must be formatted with a fast sector layout to get the full benefit.
- Hyper Speed. For DOS versions without UltraSpeed support, the ROM holds a small high-speed driver that it can load into the computer before booting a disk. Switch the drive to D1:, boot the computer with no disk, insert a disk and press 1 to put the driver in page 1 (
$100–$17F) or 6 to put it in page 6 ($600–$67F). ESC boots normally. The "BOOT ERROR" message you see first is deliberate. It is the only way to make the Atari boot the disk you inserted. - Twelve formats from the standard format command: single, medium (enhanced) or double density, single- or double-sided, each in a normal or UltraSpeed layout. It always writes without verify, which Dorndorf considered too slow to be worth it. High-density (1.44 MB) formatting isn't possible.
- Partitions. In mode M, a disk is split into two (5.25-inch) or four (3.5-inch) partitions that appear as consecutive drive numbers, each holding the contents of one 5.25-inch disk side in any density. Mode F does the same but checks the density each time you switch partitions. Modes A–D boot a chosen partition, and mode S reads double-sided disks in the older standard layout used by the HDI interface.
- Better density detection, plus an optional microswitch on the drive door for 1050-style automatic detection. This one does need soldering: pin 35 of the 8040/8050 controller goes to ground when the lever is open.
- New SIO commands for programmers: track analysis (
g), universal formatting with arbitrary sector layouts (e), and reading or writing deliberately bad sectors (t,u). Together they let a copier duplicate copy-protected disks. A read command can also fetch the two halves of a 512-byte ST or PC sector.
Installation
- Remove the four screws underneath the XF551 and lift off the cover.
- Remove the four screws that hold the mechanism's metal bracket and swing the mechanism aside. You can unplug its ribbon cable, but note the orientation first.
- Lever the 28-pin ROM out of its socket. Fit the Hyper-XF EPROM with its notch facing the front of the drive. A reversed chip will be destroyed.
- Reassemble, set the rear DIP switches to drive 1 (both down), and switch on. The head should move in and out once. Boot the computer without a disk and the Hyper-XF menu with Dorndorf's copyright should appear.
3.5-inch conversion: the manual describes a solder-free swap to a standard 720K PC drive. You need the drive, a 5.25-inch mounting frame, a Shugart edge-connector adapter and a power adapter. Early XF551s with Mitsumi mechanisms also need a ribbon-cable extension. The PC drive must be configured as drive A: (not B:). Line up the red stripe on the ribbon cable with pin 1, and fit version 1.0B.
Software
The original package included the burn files HXFA.OBJ (5.25-inch) and HXFB.OBJ (3.5-inch), HMODE.COM to set the operating mode, HSIO.COM (a Hyper Speed driver for BeWe DOS) and HPATCH.BAS, which patches XDOS, Turbo-DOS and Bibo-DOS for Hyper Speed. Dorndorf planned further utilities (copiers, a disk map, ST/PC file readers) and published DOS patches in the ABBUC Magazin. An XFTOOLS.ZIP package has circulated on AtariAge. The QMEG+OS 4.0 operating system recognises a Hyper-XF drive automatically.
Tips and pitfalls
- With DD media in a 3.5-inch drive, use proper DD disks. HD disks with the hole taped over may work, but can cause read errors later.
- Hyper-XF doesn't record which mode a disk was formatted in. Use mode S only when you have to, then switch back to X.
- When partitions have different densities, the door microswitch can't tell, because the disk hasn't been changed. Use mode F instead.
- For other ways to upgrade the drive, see the XF551 entry, the XF35 kit and the Speedy XF conversion.
Credits
- Picture: An Atari XF551. Hyper-XF replaces the 8 KB ROM under its drive mechanism. — Raimond Spekking (derivative work: Schnurrikowski), Wikimedia Commons (CC BY-SA 4.0)
- Stefan Dorndorf — Hyper+ XF 1.0 Manual (English machine translation, Anleitung_eng; German original Anleitung/HYPERDOC), Nir Dary collection — Stefan Dorndorf; Pigwa.net Atari archive
- Hyper+ XF file list (Readme_eng) and OS README — Readme_eng
- comp.sys.atari.8bit FAQ, section 3.2.3 (XF551 third-party upgrades) and 7.3.3 — Michael Current (comp.sys.atari.8bit FAQ)
- QMEG+OS 4.0 description (lists hyper+ XF among supported drives)
