Microbits MPP-1000 Modems (and Supra 300AT)
- Year
- 1982
- Type
- Peripheral
- Category
- 300-baud modems connecting through a joystick port
- Manufacturer
- Microbits Peripheral Products (Albany, Oregon), later Supra Corporation
Overview
In the early 1980s, getting an Atari online normally meant buying an Atari 850 Interface Module plus a standard RS-232 modem. Microbits Peripheral Products (MPP) of Albany, Oregon skipped the interface. Its MPP-1000 modems plugged into a joystick port and handled the serial timing in software. That made them some of the cheapest ways onto a bulletin board or CompuServe. MPP later became Supra Corporation (same town and phone number). In 1986 the last of the line was re-badged as the Supra 300AT.
Models
| Model | Year | Features | Connection | Software |
|---|---|---|---|---|
| MPP-1000 | 1982 | 300 bit/s, Bell 103; no auto-dial or auto-answer (same unit as Anchor Signalman 300-232 09F) | Controller jack 4 (400/800 only) | Smart Terminal on tape and disk |
| MPP-1000C | 1983 | Auto-dial and auto-answer (same as Anchor Signalman Auto300-232) | Controller jack | Smart Terminal cartridge, CompuServe DemoPak |
| MPP-1000E | 1985 | Auto-dial and auto-answer; later sold and supported by Supra | Controller jack | Smart Terminal cartridge, CompuServe DemoPak |
| Supra 300AT | 1986 | Supra-branded MPP-1000E | Controller jack | Smart Terminal disk, CompuServe DemoPak, Delphi membership |
Antic's December 1986 Shoppers Guide listed the 300AT ("formerly the MPP 1000-E") at $49.95. Its Smart Term software handled uploading, downloading, auto-dial, auto-answer and XMODEM transfers.
How it works
The joystick port's data lines are wired to the PIA, so software can toggle and read them directly. MPP's driver bit-bangs 300-baud serial through these lines. That's why the modems needed MPP's own terminal software, or programs with MPP drivers. Anchor Automation's Volksmodem "F cable" later used the same approach and the same MPP-1000C/1000E/300AT driver software. Standard 850-based terminal programs don't see an MPP modem unless they include such a driver.
Known issues
In December 1986 a well-known Atari telecommunications programmer pointed out in Antic that the 1000-C and 1000-E only hang up the line when they originated the call. On calls they answered, they stay off-hook, which is a problem for anyone running a BBS. Supra offered modification instructions. Antic also confirmed in 1984 that the PLATO service worked with MPP modems.
Using one today
- An MPP modem needs a joystick port: port 4 on a 400/800 for the original MPP-1000, any port for later models where the software allows. XL/XE machines have only two ports.
- 300-baud modems are now mainly of historical interest, but the Smart Terminal software and MPP drivers are worth preserving. Many period BBS programs supported "MPP" alongside "850".
- For actually going online today, a networked SIO device or Wi-Fi modem is far more practical than a phone-line modem.
Credits
- Picture: The Supra 300AT, the renamed MPP-1000E. — Photo from Gury's Atari 8-bit Forever portal (Supra 300AT) (Unknown, used for identification)
- comp.sys.atari.8bit FAQ (Michael Current), section 5.1.2 (MPP-1000, 1000C, 1000E, Supra 300AT, Volksmodem F cable) — Michael Current (comp.sys.atari.8bit FAQ)
- Antic Vol. 5 No. 8 (December 1986), Shoppers Guide: Supra 300-AT; and I/O Board: MPP Hangups — AtariMagazines.com (Kevin Savetz), 1986
- Antic Vol. 5 No. 8 (December 1986), I/O Board: MPP Hangups — AtariMagazines.com (Kevin Savetz), 1986
- Antic Vol. 3 No. 6 (October 1984), I/O Board (PLATO and MPP 1000C) — AtariMagazines.com (Kevin Savetz), 1984
- Antic Vol. 2 No. 8 (November 1983), MPP-1100 review (MPP address and phone, Albany OR) — AtariMagazines.com (Kevin Savetz), 1983
