Atari 820 40-Column Printer

Year
1980
Type
Peripheral
Category
Printer (40-column dot-matrix impact, roll paper)
Manufacturer
Atari, Inc.
Atari 820 printer with roll paper emerging from the top

Overview

The 820 was the printer Atari showed alongside the 400 and 800 from the very first previews in January 1979, and it shipped in the summer of 1980. It is a small impact printer that prints 40 columns of 5×7 dot-matrix characters on narrow 3⅞-inch roll paper — standard adding-machine rolls — fed out of the top of a case that matches the 810 disk drive (both were designed by Roy Nishi and Russell W. Farnell). It connects directly to the SIO bus and is supported by the operating system's built-in P: device, so LPRINT and LIST "P:" work with no extra software.

The 820 is also historically important as the device that defined the basic Atari SIO printer protocol: a status command and a "print line" command that sends a whole line at once. Every later Atari printer kept that scheme.

Specifications

Item Detail
Print method Impact dot matrix, 5×7 characters (7×7 in sideways mode)
Line length 40 characters (normal); 29 characters (sideways)
Speed About 40 characters per second
Character set Upper and lower case ASCII in normal mode; a reduced upper-case set when printing sideways
Paper 3⅞-inch roll paper (Atari C014062), paper mandrel C014853, ribbon C014854
Electronics 6507 CPU at 1 MHz, 6532 RIOT (I/O and 128 bytes of RAM), 2 KiB ROM
SIO Device address $40; commands Status ($53) and Write/Print Line ($57)
OS device names 400/800 OS: P: (device number ignored); XL OS: P: and P1:
Connection 2 SIO ports; 3-ft SIO cable included
Power 120 V AC built-in supply (North America only); 18 W
Made in USA, by Atari

History

At the June 1979 CES the 820 was listed at $599.99, and in June 1980 it was "again promised" at $599.95 for summer delivery — it finally shipped around mid-1980, after the 810 disk drive. Pre-production units carry an older logo with the word "Atari" inside the Fuji symbol. Atari published both an operator's manual (C014762) and service manuals (January 1980 and July 1981). With only 40 columns on narrow paper, it was soon overshadowed by the 822 thermal printer and the 80-column 825; in the XL era the 1020, 1025 and 1027 took over.

How it prints

Each print command carries one full line. An orientation byte selects normal printing (40 characters, read left to right) or sideways printing (29 characters rotated 90°, laid out right to left). The 820 ignores the end-of-line codes the OS inserts into the buffer and simply prints any unsupported character as a space, so every line sent must be padded to its full length with spaces or EOL characters. Ordinary BASIC printing works because the 820 is native to the OS P: device:

10 LPRINT "HELLO FROM THE ATARI 820"
20 LIST "P:"

Using it today / Known issues & tips

  • Paper and ribbons. Any 3⅞-inch adding-machine roll fits; the original ribbon is the same part used in some Addressograph/Multigraph and Eaton cash-register printers.
  • Using sideways mode. Bill Lukeroth's "Pocket Calendars for 1984" (Antic, January 1984) turned the 820's narrow strips into wallet calendars, and its "Sidewinder" variant used the sideways characters — which he thought looked better than the normal ones — so it runs only on an 820.
  • Labels. Fan-fold label stock is too thick for the 820; Antic suggested roll-type file-folder labels instead.
  • Voltage. North American units have a built-in 120 V supply; there was no factory 220/240 V version.
  • Emulation. Altirra emulates the 820 at the SIO level, so programs that print can be tested without the hardware.
  • Compatibility. It works with any 8-bit Atari via SIO. Software that assumes 80 columns (word processors) will wrap badly on its 40-column line.

Credits