Atari 400/800 Field Service Testing: SALT II, Symptom Checklist and Controllers

Year
1983
Type
Component
Category
Atari service procedure: the Memo Pad check, SALT II test cartridge, symptom checklist and controller tests
Manufacturer
Atari, Inc.
White cover of the Atari 400-800 Home Computer Field Service Manual with a large outlined ATARI logo and the number FD100001, Rev. 02, May 1983

Overview

Atari's 400–800 Home Computer Field Service Manual went through several editions. The module-by-module theory in the June 1982 edition is summarised in 400/800 internal boards. The May 1983 edition (FD100001, Rev. 02) has ten sections, including separate diagnostic flowcharts for the 400 and the 800, a symptom checklist "for the more experienced technician", a section on game controllers, and a service-bulletin section. This page covers its testing procedure: what an authorised service centre did with a dead or flaky 400 or 800 before SuperSALT and the XL era (see SuperSALT).

The kit was short: a 15 MHz oscilloscope, the SALT II (Stand Alone Test) cartridge, a peripheral-port test connector, a controller-jack test connector, and a properly adjusted TV.

Before the cartridge

  1. Memo Pad. With no cartridge, switch on. "ATARI COMPUTER – MEMO PAD" should appear at the top left. If it doesn't, no later test result can be trusted.
  2. Keys in Memo Pad. Type every key, with and without CTRL to check the graphics characters. One dead key points to the keyboard. Several dead keys call for further tests.
  3. Boot SALT II (in the 800's left slot). If the SALT header appears, the CPU, OS ROMs and lower RAM work. A green or yellow screen means a bad OS ROM: swap the ROMs one at a time to find it. SYSTEM FAILURE means bad lower RAM. On a 400, swap the RAM board. On an 800, move the suspect front RAM card to the third slot behind the OS so SALT can test it later. If swapping RAM and ROM doesn't help, swap the CPU board. Before blaming a board, clean its edge connector and test it again.

The SALT II tests

Type the red command letter, then RETURN:

Key Test What a pass looks like
C Colour bars A 15-colour rainbow above a reference bar. Adjust R309 until the bars directly above and below it are the same golden-rod colour. Watch for 60 seconds
A Any video A black screen with eight vertical bars, half narrow and half wide, a shaded bar across the top, and two Vs (normal and inverse). Also checks ANTIC for pattern sensitivity
G Grey bars Eight even bars from black at the top to white, steady, with no colour anywhere. Checks the CTIA/GTIA luminance lines
K Keyboard Each key echoes. Then CTRL-A shows CTRL, and each SHIFT with A shows SHIFT. Ends with KEYBOARD PASS or FAIL, with bad keys shown in red
S Console switches Press START, SELECT, OPTION, then SYSTEM RESET to get PASS or FAIL
T Tone Pick a POKEY voice from 1 to 4. Eight descending tones fade from loud to soft, and the first three may be too high to hear
D Display mode Chooses a pass/fail display or an error matrix for the next three tests, run once or continuously
P Port With jumpers on the controller and peripheral ports, a matrix of 0s. A red 1 marks a failing line, decoded with the manual's port-test legend
V Verify ROM Checksums for each ROM and the floating-point package, each marked PASS or FAIL
R RAM Tests memory block by block, with a pass counter and a red error counter

Symptom checklist

Each symptom gives likely parts (Atari's board numbers) and a page to enter the 400 or 800 flowchart:

  • Snowy screen: switch box, adaptor, channel switch, modulator adjustment, RF cable.
  • Black or grey screen: check the +5 V, −5 V and +12 V supplies and their diodes and capacitors, then regulator A201 and the chips A103, A111 and A301–A303, decoders Z103–Z105, the clock transistors Q103/Q104 and crystal X101.
  • Green or yellow screen: the ROM board.
  • Solid blue screen: A101, Q107, X101.
  • No or bad colour bars: the R309 adjustment, A301–A302 on the CPU board, A111 and Q107 on the main board, X101, Q103/Q104.
  • No grey bars: A301, A111, Q107, R309, X101, the modulator.
  • Upside-down characters or players: A302 on the CPU board, A301, A111, Q107.
  • All keys dead: A101, Z103/Z104. Some keys dead: the keyboard.
  • Missing tones: A101 and the sound-oscillator parts, including Q105, L101, Q106 and L118.
  • Console keys dead: A301, R119–R122, C121–C124.
  • ROM test fails: A401–A403 on the ROM board.
  • RAM test fails: read the RAM-test matrix.

Controllers

Section 8 describes Atari's controllers and how they were checked. Inside a joystick are five calculator-style keypads on a small board, four under the stick and one under the button. Pushing diagonally closes two at once, giving eight directions. The manual notes that earlier sticks had a spring-loaded button. Each paddle is a 1 MΩ potentiometer with a push-to-make button, and two paddles share each jack. The bench tests used real games. Joysticks were checked with Star Raiders, moving the stick in all eight directions. Paddles were checked with Super Breakout: the button serves a ball and the knob moves the paddle under it, for each paddle in turn. See joysticks and paddles for the controllers themselves.

Opening a 400

The disassembly section starts with cautions that still apply. Don't mix up screws. Tighten no more than 6 inch-pounds into plastic and 10 into aluminium. Work on a soft, grounded pad. To get at the keyboard and power supply, remove four screws from the base and unhook the top cover from the keyboard. Then remove one keyboard screw and lift the keyboard's left end to unplug its ribbon cable. For component-level checks on the 400, see Sams CC5, and for the 800 see Sams CC7.

Credits