msc-IDE Controller
- Year
- 1996
- Type
- Interface
- Category
- IDE hard disk interface (parallel bus)
- Manufacturer
- msc (Stefan Birmanns and Matthias Belitz), Germany
- Tags
- hard-disk, ide, pbi, eci, partitions, germany, msc, cd-rom, third-party, 1990s
Overview
The msc-IDE Controller is a hard disk interface for the Atari XL, designed in 1995-96 by two German students, Stefan Birmanns and Matthias Belitz, who sold it as "msc". It's a true parallel bus (PBI) device. Its driver lives in the board's own ROM and is switched in only when the OS calls it, so it uses no user memory, works with almost any DOS, and can boot the computer directly from the hard disk. It connects ordinary IDE/ATA (AT-bus) hard drives, and with the supplied utilities an ATAPI CD-ROM and the internal IDE Iomega Zip drive. On XE machines it works through a cartridge/ECI parallel-bus adapter.
The controller sold out long ago and is only found secondhand. Its command set is partly compatible with the Polish KMK/JŻ IDE interface, so tools like SysInfo work with both.
Specifications
| Item | Value |
|---|---|
| Designers | Stefan Birmanns, Matthias Belitz ("msc"), Germany |
| Year | 1995-1996 (manual dated 24 November 1996) |
| Connection | Parallel bus via a short 50-pin ribbon cable; XE through an ECI adapter |
| Drives | Up to two IDE devices (master/slave): two hard disks, or a hard disk and a CD-ROM |
| Partitions | Up to 240 per hard disk, each with an eight-character name |
| Emulated drives | D1: to D9: at the same time, with any partition on any drive number |
| Partition size | Up to 65,535 sectors of 256 bytes (16 MB) with a suitable DOS |
| Boot | From any partition, with the standard XL OS |
| Write protect | Per-partition software "write-protect tab" |
| Speed | Over 30 KB/s reading and over 10 KB/s writing with SpartaDOS 3.2gx (file access) |
| Registers | $D108-$D10F (ATA task-file registers, data low byte at $D108), $D120 (data high byte, for 16-bit transfers), $D1FF (device select); ROM at $D800-$DDFF |
| Power | From PBI pin 47 (600XL, most XE adapters) or a PC floppy-style power connector on the board |
| Software | INSTALL, SETUP, FDISK, MAP, LMAP, HDINST, IMG2DISK, CD utilities (CDPLAY, CDREAD); supplied on a BW-DOS 1.30 disk |
How it works
The Atari OS supports up to eight parallel-bus devices. Each has its own ROM at $D800-$DFFF and I/O space at $D100-$D1FF, mapped in when the OS selects that device's ID. A jumper on the msc board sets its device ID, which only matters if you have other PBI devices. Once switched in, the msc ROM answers disk calls for whichever D: numbers you have mapped to hard-disk partitions. All other drive numbers pass through to the real floppy drives.
The setup is done with a handful of programs:
- SETUP stores the drive geometry (from a type list, entered by hand, or detected with
I), installs the mapping utilities, and can invert the OPTION key so the computer boots without BASIC unless you hold OPTION. - FDISK creates and names partitions, up to 240 per disk.
- MAP assigns up to nine partitions to D1:-D9:, marks partitions write-locked, and can save the layout permanently or just for the session. Installed into the disk's system area, it pops up from anywhere with RESET+HELP, even without DOS. It borrows a page of RAM-disk memory, or wipes
$4000-$7FFFon a machine without extra RAM. - LMAP is a lighter swapper for unexpanded machines. It's called with RESET+M and exchanges the partitions on two drive numbers to simulate a disk swap.
- HDINST formats partitions for SpartaDOS or BW-DOS. IMG2DISK writes
.ATR/.XFDimages (single or enhanced density) to a partition or disk under SpartaDOS 3.2 or BW-DOS.
The ROM adds two handy key combinations: RESET+SHIFT forces a cold start without power-cycling, and RESET+INVERSE disables the controller for one boot so the floppies take over again. With no drive attached, or a faulty one, the computer waits about ten seconds at power-up to let the drive spin up before continuing.
Using it today
- Pick a large-volume DOS. Atari DOS 2.5 only handles partitions up to 130 KB. MYDOS 4.50, SpartaDOS 3.2f/3.2gx and BW-DOS can use partitions up to 16 MB.
- Power carefully. On an 800XL (or a 600XL with a 1064) you must either run +5 V to PBI pin 47 or power the board from its own connector. Never feed it from both at once, the manual warns. The hard disk always needs its own power supply.
- Utilities. The final utility versions from the authors are SETUP 1.13, FDISK 1.10, MAP 1.10, INSTALL 1.03 and LMAP 1.03. Older FDISK versions could create more than 240 partitions, which caused trouble, so use the updated set.
Compatibility
- Computers: 800XL (PBI) directly. 600XL with power from the PBI. 130XE and other XE models via an ECI parallel-bus adapter.
- DOS: any DOS for booting through D1:, with SpartaDOS, BW-DOS and MYDOS needed for large partitions.
- Related devices: KMK/JŻ IDE and IDE Plus 2.0 (Poland), MyIDE, SIDE and the ICD Multi I/O.
Credits
- Picture: The msc-IDE controller board and its short 50-pin parallel bus cable. — Photo from Gury's Atari 8-bit Forever portal (gury.atari8.info), MSC IDE-Controller entry (Used for identification; copyright of the original photographer)
- Stefan Birmanns, Atari XL page: IDE-Hostadapter (birmanns.de) — Stefan Birmanns
- msc-IDE Controller manual (Anleitung, 24.11.1996) and update notes (21.12.1996), birmanns.de downloads — birmanns.de, 1996
- comp.sys.atari.8bit FAQ (Michael Current), section 3.3.4 msc-IDE Controller — Michael Current (comp.sys.atari.8bit FAQ)
- Atariki: Msc (Polish) — Atariki contributors
- Gury's Atari 8-bit Forever: MSC IDE-Controller — Photo from Gury's Atari 8-bit Forever portal (gury.atari8.info), MSC IDE-Controller entry (Used for identification; copyright of the original photographer)
