IDE Plus 2.0 (and KMK/JŻ IDE)
- Year
- 2011
- Type
- Modern device
- Category
- Parallel-bus ATA/CompactFlash hard-disk interface with SpartaDOS X flash and RTC
- Manufacturer
- Jacek Żuk (Simius), hardware; Konrad M. Kokoszkiewicz (drac030), firmware
Overview
The IDE Plus 2.0 (2011) is the mature form of a Polish hard-disk interface line that goes back to the KMK/JŻ IDE of 1996. Hardware designer Jacek Żuk (Simius) and firmware author Konrad M. Kokoszkiewicz (drac030) built a parallel interface that lets an XL/XE talk directly to standard ATA (IDE) hard drives, CompactFlash cards and, at the hardware level, ATAPI devices. Because it sits on the parallel bus rather than the slow SIO, it's fast: 50-80 kB/s in native mode. Its BIOS is fully Atari OS compliant, so no OS patches are needed, and it can boot from any partition. Version 2.0 adds flash memory for SpartaDOS X and a real-time clock on the same board.
Specifications (IDE Plus 2.0)
| Item | Value |
|---|---|
| Connection | Both PBI and cartridge+ECI connectors; cartridge pass-through |
| Power | From the computer (no external supply) |
| Drives | ATA-3 or later; two drives supported; CF cards |
| BIOS | 96 KB ISP flash ROM plus 32 KB RAM for the PBI BIOS, flashable from the Atari |
| SpartaDOS X flash | 512 KB or 1 MB, flashable; can be disabled with a switch |
| Clock | Real-time clock for SpartaDOS X |
| Activity | LED flashes during I/O |
| Capacity | Up to 268,435,456 sectors per device (128 GiB) |
| Partitions | Up to 16; independently write-protectable |
| Sector sizes | 512 bytes native, 256 or 128 bytes emulated |
| Speed | 50-80 kB/s native; 30-45 kB/s emulated |
| Data path | 16-bit transfers |
History
The original KMK/JŻ IDE (1996, revised as version 1.2 with more memory) was a cartridge+ECI device for the XE. It handled drives up to 8 GiB and 16 partitions, with emulation modes for 256- and 128-byte sectors so ordinary DOSes could use it. IDEa (2005) by Michał "Pasiu" Pasiecznik was a clone that could also be mounted inside any XL/XE. The 2.0 redesign moved to both PBI and ECI and fixed a long-standing problem: the PHI2 clock signal differs between XL and XE motherboard revisions and with other expansions installed, which had made earlier interfaces fussy. It also brought SpartaDOS X and the clock on board.
Using it today
- Drive support follows the ATA standard. Choose ATA-3 or later drives, or CF cards in a CF-to-IDE adapter.
- Partition and format using the utilities from drac030's site. Partitions can use native 512-byte sectors under SpartaDOS X for speed, or emulated 256-byte sectors for compatibility with other DOSes.
- SpartaDOS X has drivers for the KMK/JŻ family and IDEa, so the same disks move between generations.
- The BIOS doesn't support ATAPI (CD-ROM) devices, although the hardware can attach them.
Credits
- Picture: An IDE Plus 2.0 board. — Photo from the Atariki article 'IDE Plus 2.0' (atariki.krap.pl) (Used for identification; copyright of the original photographer)
- comp.sys.atari.8bit FAQ (Michael Current), section 3.3.4 (KMK/JZ IDE, IDEa Interface, IDE Plus 2.0) — Michael Current (comp.sys.atari.8bit FAQ)
