BTL Hard Disk System

Year
1986
Type
Storage
Category
Hard disk interface (SASI, parallel bus)
Manufacturer
William Lurie & Associates (BTL), Van Nuys, California

Overview

The BTL Hard Disk System was one of the first ways to put a real hard disk on an Atari XL or XE. It came from William Lurie & Associates of Van Nuys, California, and Antic first saw it running at the San Jose Atari Expo in September 1986. The system pairs ordinary hard-disk hardware (a drive and a standard SASI controller) with BTL's own Atari interface boards. The adapter's firmware handles everything without taking any of the computer's memory. Up to two physical drives give a theoretical maximum of 128 MB, divided into as many as eight logical drives of up to 16 MB each. MYDOS 4 came with every system, and ICD's SpartaDOS 3.2 worked too.

Specifications

Item Value
Maker William Lurie & Associates, Van Nuys, California
Introduced 1986 (shown at the San Jose Atari Expo, September 1986)
Components BTL 2004 SASI Hard Disk Adapter plus a computer connector: BTL 2001 (PBI, for the 800XL) or BTL 2002 (cartridge slot + ECI, for the 130XE, with a cartridge pass-through)
Disk interface SASI, 50-pin ribbon cable; controller must support 256-byte sectors
Drives One or two physical hard disks
Capacity Up to 128 MB total; up to 8 logical drives of up to 16 MB
Systems sold 10 MB standard; complete packages up to 60 MB (1987) and later 85 MB
Power Interface boards powered by a small plug-in DC adapter
Software Firmware with format/partition menu and head parking; MYDOS 4.x included
Price $550 for 10 MB with MYDOS (Antic Shoppers Guide, January 1988)

History

Antic's Bill Marquardt reviewed an advance unit for the April 1987 issue. BTL shipped the drive and its case in two boxes, and putting them together took a couple of minutes: a few plugs and four screws. The 2001 or 2002 connector plugs into the back of the computer and the 2004 adapter plugs into the connector. Marquardt warned that the bare boards need about ten inches of clear space behind the Atari and suggested a proper case would be a worthwhile upgrade. BTL also sold just the adapter and connector to owners who had their own SASI drive and controller.

He found the system "reliable and efficient" at a price that brought hard disks "within reach of many 8-bit Atari users". By the January 1988 Shoppers Guide, BTL listed complete packages up to 85 MB, with the 10 MB system at $550.

How it works

BTL drives arrived formatted, so the computer would boot straight from the hard disk once the drive was up to speed. To set up your own drive, you switch the computer off, flip a small switch on the interface and power up again. The interface's firmware then shows a menu for formatting and partitioning. Partition sizes are entered in hexadecimal sector counts, so you need to convert from decimal. Each partition then gets a DOS format, either with MYDOS (which needs its drive assignments reconfigured) or with SpartaDOS 3.2.

Booting. Holding SELECT at power-on boots from floppy drive 1 instead. In the early firmware the hard disk's logical drive 1 simply replaced floppy D1:. Later firmware "bumps up" the drive numbers by one, so the hard disk's first partition becomes D2: and remains available alongside the floppy. Later firmware also added a head-park command for moving the drive.

Using it today

  • Find a compatible controller. The adapter only works with SASI controllers that support 256-byte sectors, so check a controller's sector-size options before relying on it.
  • Keep the firmware current. If you can, use a unit with the later firmware for the renumbered boot drive and head parking. Park old MFM drives before moving them.
  • Partition for your DOS. MYDOS handles the large partitions well. Remember each logical drive is capped at 16 MB.
  • Modern alternatives. Today IDE and CompactFlash interfaces (such as MyIDE, KMK/JZ IDE, SIDE and Incognito) or SD-based SIO devices do the same job with far less hardware. A working BTL setup is mainly a collector's piece.

Compatibility

  • Computers: 800XL via the BTL 2001 (PBI), 130XE via the BTL 2002 (cartridge + ECI).
  • DOS: MYDOS 4.x (supplied) and SpartaDOS 3.2. Atari DOS 2.x can't use partitions this large.
  • Related: SupraDrive (Supra Corp.) and the ICD Multi I/O board were the other 1980s hard-disk routes for the 8-bit Atari.

Credits