Indus GT Field Service Manual
- Type
- Component
- Category
- Third-party service documentation: Indus GT self-tests, GT-DOC diagnostics, common faults and ROM revisions
- Manufacturer
- Indus Systems, Inc.
- Tags
- indus-gt, disk-drive, service, repair, field-service-manual, z80, wd2797, tandon, diagnostics, gt-doc, rom-revision, synchromesh
- Related
- Atari 1050 Service Manuals (Atari Field Service Manual and Sams Computerfacts CD13), Atari 1050 Firmware Revisions and Drive Mechanisms, Atari 1020 and 1027 Printer Field Service Manuals, Atari 1025 Printer Service Manuals (Atari Field Service Manual and Sams Computerfacts CP21), Atari 410 and 1010 Program Recorder Service Manuals, Atari 810 Troubleshooting (Sams Computerfacts CD9)
Overview
The Indus GT was the stylish black third-party drive with a smoked sliding dust cover, a front LED display and control buttons. Indus Systems wrote a Field Service Manual for "the Atari compatible model" aimed at technicians rather than engineers. It says nearly every repair needs no electronics knowledge. Repairs stop at the chip level: a technician may replace socketed ICs, connectors and listed parts, and anything else on a board means returning the board to Indus for an exchange. The manual has chapters on disassembly, diagnosis by the drive's own self-tests, diagnosis with the GT-DOC program, troubleshooting, Tandon mechanism repair, and schematics.
What's inside
The drive uses a half-height Tandon TM50-1 single-sided mechanism. An analog board on top of the mechanism carries the read, write and motor-control circuits. The digital board lies flat in the bottom of the case. Indus called it the WART board, from the project's original name, "Wonderful Atari Rotating Thing". It holds a Z80A CPU, its control EPROM, a 6116 2K static RAM buffer and a Western Digital 2797 floppy controller. At the back are two 13-pin SIO sockets, the power socket and switch, and a four-way DIP switch.
Unlike Atari's drives, the Indus runs from an external supply that delivers 12.2–13.0 V DC. Plugging an Atari AC adaptor into it simply leaves the drive dead, and the manual says it shouldn't cause damage.
The self-tests
Level one runs at every power-on and shows codes on the LED display as it goes. It checks the Z80A's flags, accumulator, registers and stack pointer, then the EPROM checksum (code H0 on failure), then a checkerboard test of the 6116 RAM with $55AA and $AA55 patterns (H1). Next come the Z80's index registers (HE) and a detailed check of the floppy controller (H3), which tests its interrupt, register read-back and index-pulse detection.
Level two is for technicians. Make a test plug from a bare 13-pin SIO connector, shorting pins 1, 2 and 7 together and pins 3, 5 and 10 together. Plug it into either SIO socket with nothing in the other. Then hold TRACK, ERROR and DRIVE TYPE while switching on. The drive runs level one again, then a bus-interface test, an interrupt test and an extended RAM test. A good drive ends by alternating "C6" and "c6" on the display.
GT-DOC
The GT-DOC diskette boots OSS DOS (hold OPTION on a 600XL or 800XL to disable BASIC), then binary-loads GTDOC.COM. Indus recommended a two-drive setup with the drive under test as D2:. Its menu includes:
- Speed check, by two methods. The address-mark method reads track 0 sector 1 a hundred times and averages the result, to about ±0.2 rpm. The index-mark method, which works only on an Indus, times the disk's index hole. The target is 288 rpm ±4, and Indus recommended setting it to 288 ±1. A speed that wanders more than half an rpm between readings needs attention.
- Configuration inquiry. This shows 40 tracks and a 20 ms step rate for all modes. Single density is 18 sectors of 128 bytes, Indus's "dual" density is 26 sectors of 128 bytes (Atari's enhanced density), and double density is 18 sectors of 256 bytes.
- FDC type (WD177x or WD279x, decided by timing the controller's response), random read/write tests, head positioning, and a check-disk routine.
Common faults the manual describes
- Dust cover won't open. Its dowel-pin hinges get knocked out of line if the cover is pressed from above, or the cover warps in heat, for example in a hot car. A missing door spring or a failed hydraulic damper causes the same symptom.
- Springs. Check the door-latch spring, the cover spring, the felt pressure-pad spring (without it reads and writes are unreliable) and the ejector spring. A fifth spring found in some drives "serves no useful purpose".
- Connectors. Look for bent SIO pins and cracked solder joints on the DIP switch. A drive that won't change its drive number may have a broken DIP-switch joint. Wires in the 20-pin ribbon can break where it meets the WART board, and wires into J1/J3 on the analog board snap when the housing is slid off. One telltale is a motor racing at over 700 rpm.
- Write-protect sensor. If the motor won't switch off, the sensor may be bad. Shorting the middle two pins of the centre WART connector bypasses it for a test, but this also disables automatic density selection, so don't leave it that way.
- Mechanism parts. The Tandon's belt, the locking-bar cam pin and other internal parts aren't on the replaceable list. Breaking one means replacing the whole mechanism. Unlubricated head rails cause random-sector errors.
- Early power socket. Older drives have a socket that is slightly too wide and too shallow, so the plug falls out. Drives with ROM 1.2 should have the improved socket.
ROM revisions
The manual lists three EPROM releases, 1.00, 1.10 and 1.20, and tells technicians to replace 1.00 and 1.10 "immediately". Version 1.10 added code for the planned Synchromesh high-speed mode, which the manual describes as still in development, and fixed a BUSY LED that stayed lit. Version 1.20 corrected the display of verify error P9, switched a bus line from CLOCKIN to DATAOUT control, compacted the code, and added immediate diskette analysis: hold TRACK and press DRIVE TYPE, and the drive detects the disk's density and switches to it. Some GT-DOC tests also fail in dual density without 1.20. The site's Indus GT page covers later ROMs and the RAM Charger.
