XF35 Kit (3.5-inch XF551 conversion)

Year
1988
Type
DIY project
Category
Disk drive conversion kit
Manufacturer
Innovative Concepts (design by Bob Woolley)
Rear panel of a beige Atari XF551 disk drive showing the power switch, power socket, two SIO peripheral ports and the drive-select DIP switch

Overview

Atari showed a 3.5-inch drive for its 8-bit line at trade shows, then shipped the 5.25-inch XF551 instead. Bob Woolley, a hardware hacker active on CompuServe, found that the XF551's controller could drive a standard PC-style 720K 3.5-inch mechanism with surprisingly little work: remove the 5.25-inch mechanism, mount the 3.5-inch drive, plug in a new cable and fit a new EPROM. Mark Elliott of Innovative Concepts arranged with Woolley to sell it as a kit, dated 11 November 1988. Antic reviewed it in September 1989, when it cost $37.95 including shipping.

The result is a drive that stores 720K per disk, eight times a single-density DOS 2.0 disk, on media that fits in a shirt pocket.

What's in the kit

Item Purpose
Replacement drive EPROM 80 tracks instead of 40, seek timing tuned for 3.5-inch mechanisms, a spin-up delay change that improves write reliability, and density retry. XF551 high speed remains available
34-pin ribbon cable with connectors from the XF551 controller to the 3.5-inch drive
4-pin power adapter cable 3.5-inch drives use the smaller power connector
34-pin male header soldered to the controller board in place of the original cable
Instructions and schematics 18 steps for the basic conversion, plus 14 optional steps for twin drives

The drive mechanism itself was not included. Any 720K PC drive from a mail-order house would do.

Building it

Single 3.5-inch drive. The hardest step is desoldering the 34 pins of the XF551's original drive ribbon cable from the controller board. The reviewer used a 30 W pencil iron and solder wick. A header goes in its place, so cables can be swapped easily afterwards. Then the 5.25-inch mechanism comes out, the 3.5-inch drive goes in on the existing bracket, and the new ROM replaces the old one. Until you piggy-back ROMs for the twin option, the job is reversible: put the 5.25-inch mechanism and original ROM back and you have a stock XF551 again.

Twin-drive option. You keep the 5.25-inch drive and add the 3.5-inch drive in its own case, then choose between them with a switch. Only one works at a time. Extra parts: an SPDT and a DPDT toggle switch, a power splitter, a second 34-position card-edge connector crimped onto the ribbon cable, and an enclosure. The switches route +5 V, +12 V and the ROM selection, so both ROMs are piggy-backed and selected together. The guide itself notes that one three-pole double-throw switch is better than two separate switches, because it can't put a drive with the wrong ROM. Only flip it with the power off. Woolley recommended Tandy's external 720K drive for the Tandy 1000 (Radio Shack 25-1061). It sits neatly on top of the XF551 once its own interface board and cable are removed.

Using it

  • DOS: SpartaDOS 3.2d, SpartaDOS X and MYDOS 4.3x can format and use the full 720K. Use a DOS that allows more than 64 files per disk, or the space is wasted.
  • Speed: Woolley wrote a patch so SpartaDOS 3.2d could use the XF551's high-speed I/O, which nearly triples throughput. SpartaDOS X 4.20 supports it directly.
  • Not ST or PC compatible. The disks are the same size as Atari ST disks, but the format is different. The kit can't read ST disks.
  • Keep another drive or a RAM disk on the chain to make copying between 5.25-inch and 3.5-inch media easier.
  • Cracking open a new PC drive's case is likely to void its warranty, and the conversion voids any remaining XF551 warranty.

Related upgrades

Later options for the same job include CSS's XF Single and Dual Drive Upgrades (1991), which can also read MS-DOS disks, Stefan Dorndorf's Hyper-XF ROM with partitions and UltraSpeed, and Klaus Peters' Speedy XF. For the company behind the kit, see Innovative Concepts.

Credits