Atari DOS 3
- Medium
- Disk
- Year
- 1983
- Publisher
- Atari, Inc.
- Type
- DOS
- Category
- Disk operating system (menu-driven, block-based)
- Developer
- Atari (Mike Colburn, Richard K. Nordin, John W. Clark, Olivia Ying-Tzu Jang)
- Language
- 6502 machine language
- Requirements
- Atari 400/800/XL/XE with an 810 or 1050 disk drive
- Tags
- dos, atari-inc, disk, 1050, enhanced-density, 1450xld, incompatible, menu
Overview
Atari DOS 3 was Atari's attempt to replace DOS 2.0S when the Atari 1050 drive brought "enhanced" (or "dual") density: 26 sectors per track instead of 18. It shipped on the 1050's master disk from 1984 into early 1985 and was sold boxed as DX5052. On paper it was more modern than DOS 2: it stored files in 1K blocks, kept its utilities in separate files that loaded only when needed, and had an on-line help screen.
In practice it is remembered as Atari's worst DOS. It could not read DOS 2 disks without a conversion step, it had no way to convert back, and it wasted disk space. Magazines warned readers away from it for years, and Atari ended up offering a free exchange of the DOS 3 master disk for DOS 2.5.
How it works
DOS 3 divides each disk into blocks of eight 128-byte sectors (1,024 bytes):
| Format | Sectors | Blocks | Data capacity |
|---|---|---|---|
| Single density (810) | 720 | 87 usable | 89,088 bytes |
| Enhanced density (1050) | 1040 | 127 usable | 130,048 bytes |
The first three blocks hold the boot sectors, a file directory of up to 63 files and a File Allocation Table. Allocating whole blocks means even a tiny file takes 1K. Antic's 1985 survey gave the example of a 1,025-byte file using two blocks, wasting 1,023 bytes.
The software comes in layers so that you only pay for what you use:
- FMS.SYS: the resident file manager, providing
D:and the simple erase, rename, protect, unprotect and load functions. - KCP.SYS: the Keyboard Command Processor, loaded at boot if a cartridge is present. It handles save, go to address, run cartridge, copy, initialise, duplicate and the DOS 2 access option.
- KCPOVER.SYS: the menu screen itself.
- COPY.UTL, DUPDISK.UTL, INIT.UTL, CONVERT.UTL, HELP.UTL: utilities loaded from disk only when you pick them, plus HELP.TXT for the help screens.
- HANDLERS.SYS: loads the 850 Interface's
R:handler at boot if it is on drive 1.
This design leaves more memory free than DOS 2, but it means the DOS disk, or a drive holding it, must be available whenever you use the menu. One common complaint was constant swapping of the master disk.
DOS 3 also changed the meaning of BASIC's NOTE and POINT. They work with a byte offset from the start of the file instead of a sector-and-byte address, so programs that used them under DOS 2 need changes.
The compatibility problem
The ACCESS DOS 2 option (CONVERT.UTL) copies files from a DOS 2.0S disk to a DOS 3 disk. Nothing on the master disk goes the other way. Once a user had converted their library, they could no longer share disks with the many 810 owners running DOS 2.0S, or easily use type-ins and magazine disks. Programs that poked DOS 2 memory locations also failed, and DOS 3 used more memory. Antic published a method to get files back to DOS 2 in January 1985 and public-domain utilities appeared too. One trick was to copy a file to cassette from DOS 3 and back to disk under DOS 2.
Antic's July 1985 round-up of DOSes advised "Don't waste your time with Atari DOS 3!", and the magazine was still answering readers' letters about mysterious failures caused by DOS 3-formatted disks in 1988. DOS 2.5's master disk included COPY32.COM specifically to move files from DOS 3 disks to DOS 2.5 or 2.0S.
Behind the scenes
The released DOS 3 began as pre-release builds by Mike W. Colburn in late 1982 and early 1983. Richard K. (Hud) Nordin produced releases 4, 5 and 9 in 1983. John W. Clark and Nordin made Release 10 (fixing APPEND and NOTE/POINT problems, March 1984), and Clark and Olivia Ying-Tzu Jang made Release 11 (May 1984). An earlier, separate "DOS 3" project had been run in 1981 by Brian Johnston with consultant Harry B. Stewart.
DOS 3 supports both serial-bus drives and the parallel-bus integral drives planned for the never-released 1450XLD. The Introduction to the Atari Disk Operating System manual mentions the 1450XLD extensively. Atari also had another DOS, Michael Barall's QDOS, planned as "DOS 4"; it was never released by Atari but appeared in the public domain via Antic in 1986.
You can tell the release with PEEK(1816) from BASIC: 56 means Release 9 or earlier, 51 means Release 10, and 53 means Release 11.
Using it today
DOS 3 is mostly of historical interest. Disk images are easy to find and it boots in any emulator, so it is worth a look to see its help system and block-based design. If you find old disks in DOS 3 format, boot DOS 2.5 and use COPY32.COM to move the files to a DOS 2 disk. For general use, choose DOS 2.5, MyDOS or SpartaDOS instead.
Credits
- Picture: The boxed DOS 3 package (DX5052), which also came with early 1050 drives. — Disk scan from AtariMania (Fair use (packaging/screenshot for identification))
- comp.sys.atari.8bit FAQ (Michael Current) — 7.3.1 What is Atari DOS? — Michael Current (comp.sys.atari.8bit FAQ)
- Antic Vol. 4 No. 3 (July 1985) — Everything You Wanted to Know About Every D.O.S., Eric Clausen — AtariMagazines.com (Kevin Savetz), 1985
- Antic Vol. 3 No. 10 (Feb 1985) — Help! — AtariMagazines.com (Kevin Savetz), 1985
- Antic Vol. 5 No. 5 (Sept 1986) — I/O Board — AtariMagazines.com (Kevin Savetz), 1986
- Antic Vol. 7 No. 6 (Oct 1988) — I/O Board ('No DOS 3') — AtariMagazines.com (Kevin Savetz), 1988
- AtariMania — DOS 3.0 — Disk scan from AtariMania (Fair use (packaging/screenshot for identification))
