Atari Diskettes and Disk Formats

Year
1979
Type
Storage
Category
Technical reference — media, densities and on-disk layout
Manufacturer
Atari, Inc.
Black 5.25-inch floppy disk labelled Atari Master Diskette 3, DX5052

Overview

Every disk drive Atari sold for the 8-bit line — the 810, 1050 and XF551, plus the unreleased 815 — uses ordinary 5.25-inch floppy disks, and every one of them can read the original 90K single-density format of the 810. Later drives added denser formats, but because the computer asks for numbered logical sectors over SIO rather than tracks and heads, one DOS and one boot process work across all of them.

The media

Atari's own blank disks were the CX8100 (5 diskettes for the 810) and CX8202 (5 blank diskettes for the 810/815), built to Atari specification C016884. Any standard 5.25-inch disk sold as 40-track/48 TPI works — single, double or "quad" density labels are all fine, soft- or hard-sectored — with two exceptions: very early 35-track disks (discontinued by 1980), and high-density (HD) disks made for the IBM PC/AT, which the Atari drives cannot use. Atari also had a CX8111 Formatted Diskette II, pre-formatted with the faster sector layout of the 810's ROM C; it was never sold as a five-pack but came with other products, including the 810 Master Diskette II. (On the cassette side, a CX4100 twelve-pack of blank tapes was planned but never shipped.)

Densities and capacities

Format Drive Encoding Layout Capacity
Single density 810, 1050, XF551 and all others FM 40 tracks × 18 sectors × 128 bytes = 720 sectors 92,160 bytes (90K)
Enhanced ("dual"/"medium") density 1050, XF551 MFM 40 × 26 × 128 = 1,040 sectors 133,120 bytes (130K)
Double density XF551 and most third-party drives MFM 40 × 18 × 256 = 720 sectors 184,320 bytes (180K)
Double-sided double density XF551, some third-party drives MFM 2 sides × 40 × 18 × 256 360K
815 double density 815 (unreleased) MFM 720 × 256 180K, but incompatible

Atari called the 1050's mode "double density", but it is not the 180K format used by Percom-standard drives, so the community calls it enhanced density. The XF551 is the only Atari drive that does true double density and both sides of the disk; it fills side one from the outside edge in, then side two from the inside edge out, which other double-sided drives must match to share disks.

The 815 dual drive (shown in 1980, never sold) wrote double-density disks with all data bits inverted compared with every later Atari double-density drive, so its disks work only in another 815. It did, however, set the lasting convention that sectors 1–3 of a double-density disk are only 128 bytes long: the OS boot loader can only load 128-byte sectors, so the first-stage loader must fit in 384 bytes and switch to 256-byte sectors itself, as DOS 2.0's boot code does.

Physical details

  • Rotation: Atari drives spin at 288 RPM (810, 1050) rather than the PC's 300 RPM; the XF551 runs at 300. One revolution takes about 208 ms at 288 RPM.
  • Interleave: sectors are not stored in numeric order around the track, so that the next sector arrives under the head just as the drive is ready. Single-density disks normally use a 9:1 interleave and enhanced-density disks 13:1; high-speed drives can use tighter interleaves, and a disk formatted for one speed can load noticeably slower on another.
  • Boot sector header: sector 1 tells the OS how many boot sectors to load (1–255); DOS 2 uses three.
  • Sector 0 is never used, and 16-bit sector numbers limit a drive to 65,535 sectors through the standard commands.
  • Flippy disks: single-sided drives read one side at a time, so two-sided disks — Atari's own Translator disk is one, with a different version on each side — have to be turned over by hand.

The Percom configuration block

Because the original SIO disk commands have no way to ask a drive about its format, the drive maker Percom defined a 12-byte configuration block, read with SIO command $4E ("N") and written with $4F ("O"). It gives tracks per side, step rate, sectors per track, number of sides, FM or MFM, 5.25" or 8", bytes per sector and translation flags (including whether sectors 1–3 are full-size). It let DOSes switch a drive between single and double density on the fly. Atari's 810 and 1050 ignore it; the XF551 and most third-party drives support at least part of it (the Indus GT only bytes 5–7).

Using disks today

  • Old disks: prefer good-quality media; the XF551's heads press harder than other drives' and have a reputation for damaging fragile disks.
  • On a PC: with utilities such as Matthias Reichl's AtariDsk and WriteAtr, a legacy PC's 5.25-inch drive can read and write Atari double-density disks; enhanced density works only with some floppy controllers.
  • Images: an ATR or XFD image stores the logical sectors, not the physical layout, so copy-protected disks need the ATX format or flux-level images.

Credits