Buying a Used Atari 8-bit Today: Models, Checks and First Steps
Atari's 8-bit line ran from the 400 and 800 of 1979 to the XE models that sold into the early 1990s, and millions were made. That makes them easy to find today, but four decades of storage and use mean you should know what you're buying. This guide helps you pick a model, test it on the spot, and get it running.
What you'll learn: the differences between the models that matter to a buyer, NTSC vs PAL, a step-by-step inspection routine using the built-in Self Test, the power-supply trap, and how to get software onto the machine once you own it.
What you need for testing: a display with composite input (or an RF-capable TV), the seller's power supply (inspect it, see section 4), and ideally a cartridge or a modern storage device you know works.
1. Choosing a model
Key facts:
| Model | RAM | BASIC | Notes for buyers |
|---|---|---|---|
| 400 (1979) | 8–16K, 48K kit later | cartridge | Membrane keyboard, RF only, 4 joystick ports |
| 800 (1979) | 8–48K on plug-in boards | cartridge | Two cartridge slots, 4 joystick ports, modular OS and RAM boards, S-video-capable monitor port |
| 1200XL (1983) | 64K (62K usable) | cartridge | XL OS, HELP and F1–F4 keys, only 2 joystick ports, no +5V on SIO pin 10, so some peripherals that draw power from the computer won't work |
| 600XL (1983) | 16K (64K with 1064 module) | built in | Parallel Bus Interface (PBI). NTSC version is RF only |
| 800XL (1983–85) | 64K (62K usable) | built in | PBI. NTSC units have composite + luma but no chroma |
| 65XE (1985) | 64K | built in | Later units have the Enhanced Cartridge Interface (ECI) |
| 130XE (1985) | 128K (126K usable) | built in | ECI, S-video-capable, the extra 64K is used by DOS 2.5's RAMdisk and many programs |
| 800XE (Europe) | 64K | built in | Late China-built units (1991–92) often have a defective GTIA |
| XE game system (1987) | 64K | built in, plus Missile Command | Console with optional keyboard. Composite and audio phono jacks, no monitor port |
Rules of thumb:
- For most people, an 800XL or 130XE is the sweet spot: built-in BASIC, the XL/XE OS that modern software expects, 64K or more, and composite video. A 130XE adds the extra 64K and S-video.
- For 400/800-only software, or if you love the classic build, an 800 is the full-featured original. Some programs need the 400/800 OS. Most of those can also run on XL/XE machines through the Atari Translator disk or equivalents.
- Avoid the 400 as your only machine unless you want it for nostalgia. Its membrane keyboard and RF-only output make it the least practical.
- The 1200XL is collectible, but its missing +5V on SIO pin 10 and lack of built-in BASIC make it a slightly awkward daily driver. A simple resistor change restores +5V.
Don't be alarmed if BASIC reports far less than 64K free. Antic's I/O Board explained to an 800XL owner who saw FRE(0) give 37,902 that part of the address space is taken by the operating system, the screen and other overhead, and that with BASIC switched on, 8K of RAM is replaced by the BASIC ROM.
2. NTSC or PAL?
Every machine was built for its home market's TV standard. Here's why that matters:
- Speed: vertical-blank-timed code runs about 16.8% slower on PAL than on the NTSC machine it was written for. Music and games tuned on one standard play at a different pace on the other.
- Display: PAL frames have 312 lines against NTSC's 262, so some software misbehaves or flickers on the "other" standard.
- Video: your display must accept the machine's standard (60 Hz NTSC or 50 Hz PAL). French SECAM machines output SECAM composite only, with no RF.
Buy the standard that matches your region's displays and the software you care about most. PAL-B and PAL-I machines differ only in their RF channel.
3. Inspection routine (15 minutes)
- Look it over. Check for cracked cases, missing or sticky keys, bent cartridge-slot contacts, and corrosion on the SIO, joystick and monitor ports.
- Check the power supply's label before you plug anything in (section 4).
- Power on with nothing attached. An XL/XE should show the BASIC
READYprompt on a blue screen. If you see MEMORY TEST with red or green blocks unprompted, the machine has failed its startup check. - Run the Self Test. Type
BYEatREADY, or hold HELP while switching on with no disk drive powered. Choose ALL TESTS with SELECT and START. - Memory: the ROM bars should turn green and every RAM square white then green. Any red is a fault. - Audio-visual: listen for the six-note tune on all four voices, and check that colours are steady. - Keyboard: press every key. Each should flash on the on-screen keyboard (BREAK is the exception). - Check the GTIA. At
READY, typePOKE 623,64. A black screen means a GTIA or FGTIA. If it stays blue, it's an early CTIA without the GTIA graphics modes (relevant mainly for early 400/800s). Press RESET afterwards. - Try a cartridge if you have one, with the power off while inserting it.
- Test the joystick ports with a joystick game or a quick BASIC check.
PRINT STICK(0)returns 15 when centred. - Test the video outputs you plan to use: composite, and S-video where the model supports it.
4. The power supply trap
Power supplies deserve special attention:
- 400, 800, 1200XL (and the 810/1050/XF551 drives) use 9 V AC transformers.
- 600XL, 800XL, 65XE, 130XE, XEGS use 5 V DC adapters (1.5 A or 1 A types).
- The 1983–84 "Type II / Ingot" C061982 supply (made in Taiwan, type DV-512CM) is known to fail in a way that can damage the computer. If one comes with the machine, don't use it.
A supply with a higher current rating than needed is fine, but the voltage and AC/DC type must be correct. Treat any unknown or damaged supply as suspect until it has been tested.
5. Storage: drives or modern devices?
- Atari 1050: the classic choice. It's backward compatible with the 810 and adds "enhanced" (dual) density of about 130K per disk. Like the 810 it has one head, but you can flip a disk to use its back side. Check that it reads disks reliably. The correct speed is 288 RPM ±3%.
- 810: single density only.
- XF551: double-sided, double density. Uses the same 9 V AC supply as the 1050.
- Modern SIO devices (SIO2SD, SIO2USB, SIO2PC/RespeQt, FujiNet and others) emulate drives from SD cards, USB sticks, a PC or a network. For most new owners, one of these is the fastest way to load software, since disk images are what you'll find online. See our guides to SIO2PC/RespeQt, FujiNet setup and SD and flash-cart devices.
- Cassette (410/1010/XC11/XC12): works, but it's slow. See the cassette loading guide.
6. First steps once it's home
- Set up following our Connecting an Atari to modern displays guide.
- Get a DOS. DOS 2.5 is the friendliest start. See Choosing a DOS.
- To boot machine-language software on an XL/XE, hold OPTION at power-on to disable BASIC.
- If an older program crashes on your XL/XE, try the Atari Translator (see XL/XE compatibility and the Translator).
- Clean and care for it (see Hardware care and maintenance).
Troubleshooting a purchase
- No picture: wrong input or channel, wrong video standard for the display, or a dead power supply. Try composite before RF.
- Boots to Self Test instead of loading a disk: check the cables to the drive, then the drive select switches.
- Some keys dead in the keyboard test: often the keyboard connector or membrane. Factor that into the price.
- Garbled or "mirrored" cartridge graphics: a 1983 Antic reply blamed a hardware fault, possibly a slow ANTIC. Test the cartridge in another machine before deciding.
Further reading
- Your Atari Computer by Lon Poole with Martin McNiff and Steven Cook (Osborne/McGraw-Hill, 1982; XL edition later). The FAQ calls it "a classic" among introductory books.
- The Atari 130XE Handbook by Peter Lupton and Frazer Robinson (1985) and Atari XE User's Handbook (Weber Systems, 1985), both listed in the FAQ's §1.17.
- Atari owner's manuals for each model, catalogued on atari8bit.net.
Credits
- Picture: The Atari 800XL, one of the most common 8-bit models on the used market. — Evan-Amos, via Wikimedia Commons (CC BY-SA 3.0)
- comp.sys.atari.8bit FAQ (Michael Current), §1.2–1.10 models, §1.12 chips, §2.3 monitors, §3.2.2 1050, §3.2.8 modern storage, §6.2 power, §7.1.7–7.1.9 compatibility, §8.1 NTSC/PAL — Michael Current (comp.sys.atari.8bit FAQ)
- Antic Vol. 6 No. 10 (Feb 1988) — First-Time Atari Users Handbook — AtariMagazines.com (Kevin Savetz), 1988
- Antic Vol. 6 No. 3 — I/O Board: Find My RAM — AtariMagazines.com (Kevin Savetz)
- Mapping the Atari (Ian Chadwick) — location 632 STICK0 (15 = neutral), 623 GPRIOR — AtariArchives.org
- Antic Vol. 1 No. 6 (Feb 1983) — I/O Board: Flip Flop — AtariMagazines.com (Kevin Savetz), 1983
- atari8bit.net book database — Your Atari Computer; The Atari 130XE Handbook; Atari XE User's Handbook — Atari8bit.net
