Ultra Sound: Monitor-Port Audio Cable (Antic, 1983)
- Year
- 1983
- Type
- DIY project
- Category
- Audio cable
- Manufacturer
- Homebrew (Thomas Krischan, Technimetrics Computer Consulting)
Overview
In Antic Vol. 1 No. 6 (February 1983), Thomas Krischan, CEO of Technimetrics Computer Consulting of West Allis, Wisconsin, a maker of computer accessories, showed how to get the Atari's sound out of the TV speaker and into a stereo system. His opening scene has Star Raiders roaring through hyperwarp while the neighbours complain. He called it "Ultra Sound". It is just a cable, but it is still the cheapest audio improvement you can make, and the pinout is worth knowing for any A/V lead.
How it works
On machines with a monitor socket, the computer puts its mixed audio on pin 3 of the 5-pin DIN socket and ground on pin 2. The cable carries those two pins to an RCA phono plug for the "tape in" or "aux" input of a stereo or radio.
Krischan wrote the project for the Atari 800. The 400 has no monitor socket, so it would have needed internal soldering and case work. Most later XL and XE models have the same socket with audio on pin 3. The exceptions are the NTSC 600XL and SECAM 800XL/130XE/XEGS, which lack the standard socket. See video output and the monitor port.
Parts (Antic's 1983 list)
| Item | Source then | Notes |
|---|---|---|
| 5-pin audio/video (DIN, 180°) plug | Radio Shack 274-003, or APX 90002 | plastic or metal shell; shielded |
| RCA phono plug | Radio Shack 274-339 | usually sold in pairs |
| At least 10 ft of shielded cable | electrical supplier | about 0.25 in outside diameter to fit the plugs. Use 22–24 AWG stranded wire, as thick wire is stiff. Foil shielding helps in noisy rooms |
Tools: a 25–35 W pencil-tip iron, 60/40 rosin-core solder, a razor, needle-nose pliers, wire cutters and a clip-on heat sink.
Building it
- Slide both plug shells onto the cable, facing the right way, before you solder. Then strip 3/4 inch of the cable jacket from each end, trim any extra conductors, and strip 1/4 inch from the two you'll use. Match the colours at both ends.
- Clamp each plug's insert in pliers with a heat sink attached. On the DIN plug, solder audio to pin 3 and ground to pin 2. On the RCA plug, the centre pin is audio and the outer shell is ground. If the insulation starts to melt, stop and let it cool. Then reassemble the shells.
- Plug the DIN end into the monitor socket and the RCA end into the stereo's tape or accessory input. Turn the TV volume down, set the stereo to mono if it has a switch (otherwise only one speaker plays), and raise the volume slowly.
- Clean music means success. A hum means a poor connection. Check that no solder has bridged across the insert.
Variations
- Krischan suggested a crude "pseudo-stereo" by splitting high and low frequencies to different channels with a crossover, and even using the audio level to drive fans or a motion seat for flight simulators. He left the designs to the reader.
- Modern A/V cables for XL/XE usually add composite or S-Video leads from pins 4, 1 and 5. The audio wiring is the same.
- For genuine stereo, add a second POKEY. See stereo POKEY upgrades or the original Gumby build.
Krischan also offered assembled cables for readers who didn't want to solder.
Credits
- Picture: Antic's Figure 1: the 5-pin plug, with audio on pin 3 and ground on pin 2. — Figure 1 of Thomas Krischan's 'Ultra Sound', Antic Vol. 1 No. 6 (February 1983), atarimagazines.com (Magazine illustration, used for identification)
- Thomas Krischan — Ultra Sound, Antic Vol. 1 No. 6 (February 1983) — Figure 1 of Thomas Krischan's 'Ultra Sound', Antic Vol. 1 No. 6 (February 1983), atarimagazines.com (Magazine illustration, used for identification), 1983
- comp.sys.atari.8bit FAQ, section 1.15 (monitor port pinout and which models lack it) — Michael Current (comp.sys.atari.8bit FAQ)
