NCT 810 Turbo Double Density Conversion

Year
1983
Type
Upgrade
Category
Disk drive upgrade (Atari 810 double density)
Manufacturer
Neanderthal Computer Things (NCT), Irvine, California
Black-and-white photo of the 810 Turbo board seated on an Atari 810 side board, with chips labelled 2 and 3

Overview

The 810 Turbo (or 810T) was a 1983 conversion kit from Neanderthal Computer Things (NCT) of Irvine, California. It turned the single-density Atari 810 into a true double-density drive storing 180 KB per side in 256-byte sectors, the same format used by Percom drives. Most 810 add-ons, such as the Happy and Archiver boards, changed the drive's firmware and speed but left it at 90 KB per disk. The 810 Turbo replaced more of the drive's electronics than any of them, and it's the only well-known kit that brought double density to the 810.

It was sold as a kit with a large binder of software and documentation, and later units came with NCT's Mach DOS. The drive behaves like a normal 810 with old disks. It starts in double density at power-up, falls back to single density when it can't read a disk, and stays in that mode until something resets it.

Specifications

Item Value
Maker Neanderthal Computer Things (NCT), Irvine, California
Sold 1983-1984
Board design Charles L. Hosick
Firmware and utilities James M. Hugard
Drive CPU Original 6507, re-clocked from 500 kHz to 1 MHz
Disk controller WD 2791 (replaces the 810's FD1771)
Added RAM 4 KB static RAM
Firmware 2 KB EPROM, official version 1.2
Formats Single density (90 KB) and double density (180 KB, 256-byte sectors); no 1050 "enhanced" density
Extra SIO commands Read/Write PERCOM block; memory access/execute command $20
Speed Standard 19,200 bit/s SIO; Mach DOS used the upload command for faster, track-buffered transfers (Antic measured about 4x)
Price $195 (1984)
Bundled software N/DOS Generator, OS/A+ versions 2 and 4 and BASIC A+ (OSS); 810T Utilities; Mach DOS on later units

History

NCT designed the board and licensed Optimized Systems Software's OS/A+ to ship with it. Early kits included:

  • N/DOS Generator, which patched a copy of Atari DOS 2.0S into a single- and double-density DOS. It was written by Hadley V. Stacey.
  • OS/A+ version 2 on a single-density disk and OS/A+ version 4 on a double-density disk, plus BASIC A+.
  • An 810T Utilities disk with BACKEMUP (a disk duplicator), PACKEMUP (packs up to 15 programs onto one disk), REVCHECK (an RPM gauge), RECONFIGURE and DIAGNOSTICS.
  • A double-density patch for valFORTH, written by Greg Beauton.

The manual promised that an upgraded DOS, then called MACH 2XH DOS, would follow in January 1984 for the price of a $5 disk. Units sold in 1984 shipped with it as Mach DOS.

NCT installed the board for $25 plus shipping if you didn't want to do it yourself. It also sold the kit with a money-back guarantee, on condition that nobody pulled the controller or EPROM out of their sockets.

Antic first mentioned the "Turbo 810" in a 1983 I/O Board reply about double density and reviewed it in August 1984, when it sold for $195. David Duberman found the photo-illustrated, solder-free installation clear enough for novices. He reported that Mach DOS sped up transfers to about four times normal, comparable to Happy's Warp Speed. Mach DOS could also switch density automatically when reading a directory, convert files between densities, toggle write verify, and disable write protection so you could use the backs of disks without notching them. His verdict: it "works and it's a good value", at far less than a new double-density drive.

How it works

Double density needs MFM encoding, which the 810's FD1771 controller can't produce. The 810T board carries a 2791 controller, a 2 KB EPROM and 4 KB of static RAM. It plugs into the 810's side board in place of the data separator and several chips. The original 6507 CPU and 6532 RIOT are moved onto sockets on the new board, and the CPU now runs at 1 MHz, twice its stock speed. Address line A12 is decoded so the RAM appears at $0800-$17FF and the ROM at $1800-$1FFF. Like the 1771, the 2791 has an inverted data bus.

The firmware handles the standard 810 commands plus the Percom configuration-block commands, which is how DOSes switch density. Write PERCOM support is minimal: it refuses a double-sided format and otherwise looks only at the density byte. A custom command, $20, reads or writes 256 bytes of drive memory and can then jump to the uploaded code. Copy utilities like BACKEMUP use it. The 2791 could in principle handle 1050-style enhanced density, but the firmware doesn't support it.

Density switching. At power-up the drive assumes double density. When a read fails, it waits for the record-not-found timeout, flips density and tries again. That's why the first access to a single-density disk is slow. Once a density has been detected the drive keeps it until it's power-cycled or a Write PERCOM command changes it. If you power-cycle only the drive, it goes back to double density while the computer still thinks it's single. Pressing SYSTEM RESET makes the OS ask the drive for its status and fall back into step.

Installation and known issues

Fitting the kit means opening the 810, unplugging the side board, removing the RFI shield and the data separator board, and moving the CPU and PIA chips onto the 810T board. A socket extender is supplied for drives with black sockets. Drives that Happy Computing had modified at the factory had to be returned to stock first. Drives with ROM-swap upgrades didn't.

The manual is blunt about the common problems:

  • CPU brand. Most failures were caused by the drive's own 6507. NCT advised fitting a MOS Technology or Rockwell part and avoiding Synertek.
  • Speed and head condition. Double density is less tolerant than single, so the drive should run at 288 RPM, give or take 2. REVCHECK displays the speed. A clean head, correct pad-spring tension and disks certified for double density all matter.
  • DOS mixing. N/DOS and OS/A+ 2.1 disks can be read by Atari DOS 2.0S. OS/A+ 4.1 uses an incompatible format.

Using it today

An 810T-equipped drive is a rarity now. If you find one, test it first with a disk certified for double density, check the speed, and treat its age like any other 810: clean the head and the edge connectors. Modern DOSes that use the Percom block to select density, such as MyDOS and SpartaDOS, handle it as a standard 180 KB single-sided drive. It won't do 130 KB enhanced density, and its speed tricks depend on Mach DOS, so a PC link or SD-card device is the better way to move images on and off it.

The Altirra Hardware Reference Manual documents the board's memory map, firmware (V1.2, CRC32 0126A511), density logic and the $20 command in detail.

Compatibility

  • Reads and writes standard 810 single-density disks unchanged.
  • Double-density disks are compatible with Percom-standard drives (Percom, Indus GT, US Doubler 1050s, XF551 in single-sided mode).
  • No 1050 enhanced-density support, so 130 KB disks from a stock 1050 can't be read.

Credits