Full 8-Bit Parallel Interface on the Joystick Ports
- Type
- DIY project
- Category
- Parallel I/O interface
- Manufacturer
- Homebrew design (anonymous author, distributed with the JOYPORT text package)
Overview
Several 1980s magazine projects, such as Paul Swanson's printer interface in ANALOG Computing #16, used two joystick ports as a parallel printer port. All of them had the same limitation. PORTA has only eight bits, so one bit has to be given up for handshaking, leaving 7-bit data: fine for plain ASCII, useless for graphics printing or 8-bit devices. This anonymous design, circulated in the JOYPORT text package together with a joystick-port configuration tutorial, delivers a full 8-bit data bus plus four handshake lines from PORTA alone. So it works on XL/XE machines as well as the 400/800. The author used it for an almost complete IEEE-488 interface and for a ham-radio phone-patch controller.
How it works
The trick is to send each byte in two halves:
- Joystick port 1 (PORTA bits 0–3) carries a nibble of data.
- Two 74LS75 4-bit latches capture the low nibble and then the high nibble. PORTA bits 4 and 5 (on joystick port 2) enable one latch at a time. A single bit would do, but using two is slightly cleaner.
- The latch outputs together form the full 8-bit word.
- PORTA bits 6 and 7 are left over as outgoing handshake lines, for example a data-valid (DAV) strobe.
- The two joystick trigger inputs (pin 6 of each port) don't go through the PIA, so they serve as incoming handshake lines, for example a printer's BUSY or ACK.
The result is 8 data lines out, 2 control lines out and 2 control lines in. A 74LS244 octal buffer sits between the joystick ports and the rest of the circuit to protect the Atari's PIA.
Parts
| Ref | Part | Power pins |
|---|---|---|
| IC1 | 74LS244 octal non-inverting buffer | 20 = +5 V, 10 = GND |
| IC2, IC3 | 74LS75 quad latch | 5 = +5 V, 12 = GND |
| — | two DB-9 female connectors (joystick ports 1 and 2) | |
| PSU | 7805 regulator, 9 V 200 mA transformer, 1N4005, 100 µF, 0.01 µF and 25 µF capacitors |
Power: don't run it from the joystick port's +5 V pin. The author notes that pin supplies only about 50 mA, and the 74LS244 draws a fair amount, which could cause trouble if other devices also take power from the computer (an SIO-powered printer interface, for example). Build a separate 5 V supply with a 7805. An old cassette-recorder adapter makes a good source.
Joystick pins used: 1–4 data, 6 trigger input, 8 ground. Leave 5, 7 and 9 unconnected.
Programming
Atari BASIC is too slow for this kind of bit-juggling. The original article gives example routines in Action!, and the author remarks that compiled Action! code disassembles into very tidy 6502. To send one byte:
- Configure PORTA as all outputs (PACTL to
$38, PORTA to$FF, PACTL to$3C). The companion PORTCNFG text in the same package explains this step for beginners. - Write the low nibble to bits 0–3 and pulse the first latch's enable bit.
- Write the high nibble and pulse the second latch enable.
- Assert the DAV/strobe bit, then wait on a trigger input for the device's acknowledge.
In machine language this is a handful of instructions per byte, which is plenty fast for printers.
Uses
- A true 8-bit Centronics-style printer port, without an 850 interface.
- Instrument control (the author's IEEE-488 bus), relay boards, or links to other computers.
- A learning project in PIA programming. See also Joystick-Port Interfacing for the PIA basics, and the Dual PIA mod for a way to gain a whole extra port on an 800.
