Hybrid Arts MIDIMate

Year
1984
Type
Interface
Category
MIDI interface (SIO)
Manufacturer
Hybrid Arts (Bob Moore)
Promotional photo of an Atari 800XL surrounded by synthesizer keyboards, with a small MIDIMate box on top and a MIDITrack screen on the monitor

Overview

The MIDIMate was one of the earliest MIDI interfaces for the Atari 8-bit. It came from Hybrid Arts, founded by Bob Moore, previously a Hollywood studio musician. It's a small box on the Atari's SIO port with MIDI In and MIDI Out sockets, plus Sync In and Sync Out phono jacks for drum machines and tape sync. Paired with Hybrid Arts' MIDITrack sequencer it made the Atari the controller for a whole MIDI studio. The Atari's POKEY made no sound of its own: up to 16 MIDI channels went out to synthesizers and drum machines. So much software was written for it that later 8-bit MIDI interfaces copied its design.

Specifications

Item Value
Maker Hybrid Arts (Bob Moore)
Introduced 1984: shown at NAMM in January and at MIDISoft '84 (San Francisco) in May
Ports MIDI OUT, MIDI IN (5-pin DIN); SYNC OUT and SYNC IN (phono)
Connection Atari SIO; must be the last device on the chain
Enable SIO motor-control line (only one such device per system)
MIDI clock 4 MHz crystal divided by 128 → 31,250 baud, fed to POKEY as an external clock
Computers Any Atari with 48 KB (MIDITrack II); MIDITrack III needs a 128 KB XL/XE
Bundled software MIDITrack (1984), later MIDITrack II and MIDITrack III

History

Antic's June 1985 music feature, "Play It Again, Atari!", covered MIDITrack II with the MIDIMate, which cost $349 by mail or in music stores. Moore explained that he had chosen the Atari because it was "the sturdiest of the inexpensive lightweight computers", with "the best chance to survive a long professional road tour". With an Atari and disk drive already on hand, he reckoned a full professional setup would cost under $3,000, while "just having fun" could be done for $500 or less.

MIDITrack II worked like a 16-track tape recorder: independent tracks, overdubbing, transposition, speed changes, auto-locate, punch-in recording and quantization. Files held up to 3,000 notes. The manual's quick start was simply to press the space bar, play, and press it again. Antic paired it with the then-new Casio CZ-101; Moore demonstrated it with a Yamaha DX7 and RX11 drum machine.

Hybrid Arts built a whole software line around the interface: MIDITrack III (1985, 128 KB), DX-Editor for the Yamaha DX7/TX, GenPatch, MIDIPatch for the DX7 and Casio CZ-101/1000, MIDICom (MIDI telecommunications, 1986), Oasis (an Ensoniq Mirage editor, 1986) and the MIDI Music System, Synthetic Software's MIDI version of Advanced MusicSystem II. Other software adopted it too, including Kawai's K3 Wave Table Editor and the prototype 8-bit MIDI Maze by Xanth F/X (1989).

How it works

MIDI runs at 31,250 baud, a rate POKEY can't generate accurately from its normal clock. The MIDIMate solves this by dividing a 4 MHz crystal by 128 and feeding the result to POKEY as an external serial clock. Software selects it through the external-clock modes in POKEY's SKCTL register. Software then sends and receives MIDI bytes through POKEY's serial port and handles the MIDI protocol itself.

The SIO motor line enables the box. When motor control is on, the external clock and sync input are connected to the SIO bus. When it's off, they're disconnected, so disk drives earlier in the chain still work. The sync input arrives on the SIO interrupt line (the PIA's CB1 input), which lets a drum machine or tape sync track drive the sequencer's timing.

Clones and successors

Because so much software was written for it, later interfaces kept MIDIMate compatibility:

  • MIDIMax by Wizztronics (Steve Cohen), 1988, with a pass-through SIO port, shipped with the MIDI Music System;
  • MIDIMate-Interface V2 by Christoph Büssow (HardWareDoc/ABBUC), 2011, with MIDI Thru and an optional SIO pass-through;
  • MIDI Muse by Ivo van Poorten (2018), compatible apart from the SIO port triggers.

Using it today

  • Placement. An original MIDIMate must be the last SIO device. Use a clone with a pass-through if you also need an SIO2SD or FujiNet in the chain, and check that nothing else on the bus uses the motor line.
  • Emulation. Altirra emulates the MIDIMate and can route its MIDI output to the PC's MIDI devices, with a serial port option for custom MIDI interfacing. That's a convenient way to try MIDITrack or MIDI Music System files.
  • Software. MIDITrack III and Oasis need 128 KB, so use a 130XE or an expanded XL.

Compatibility

Works on any Atari 400/800/XL/XE with an SIO port and enough memory for the software. Software written for it also runs with MIDIMax, MIDIMate V2 and other MIDIMate-compatible interfaces.

Credits