Crystal Computer Products 128K and 256K RAMCard

Year
1986
Type
Upgrade
Category
Memory board for the Atari 800 (Axlon-compatible)
Manufacturer
Crystal Computer Products (CCP), The Colony, Texas

Overview

When Axlon stopped making its RAMPOWER 128 for the Atari 800, owners who wanted more memory were left with few options. Crystal Computer Products (CCP) of The Colony, Texas stepped in in 1986 with the 128 K RAMCARD. It's a bare circuit board that goes in the 800's middle memory slot and is compatible with all software written for the Axlon board. A 256 K RAMCARD followed. Like the Axlon, both cards provide 16 KB banks that switch into the 800's normal memory one at a time, which RAM-disk software and memory-hungry programs can use.

Specifications

Item 128 K RAMCARD 256 K RAMCARD
Maker Crystal Computer Products, The Colony, Texas Same
Year 1986 1986
Slot Atari 800 middle (second) RAM slot Same
Banks 8 × 16 KB 16 × 16 KB
Banking Axlon type (bank number written to $CFFF, banks at $4000-$7FFF) Same
System total 160 KB with 16 KB cards in the other two slots 288 KB
Compatibility setting Jumper J1: 16 KB or 128 KB; optional switch 16 KB or 256 KB
CDY patch Pads at J2 —
Case None (bare board, runs cooler) —
Software None from CCP; dealers could bundle their own —

How it works

The Atari 800 has three slots for memory boards behind its top lid. CCP's instructions are to keep a standard 16 KB board in slot one, put the RAMCARD in the middle slot, and keep a 16 KB board in the rear slot. The RAMCARD fits with its solder side facing the keyboard.

In 16 KB mode the card behaves like an ordinary Atari 16 KB module, for software that misbehaves with banked memory. In 128 KB mode, writing a bank number to the Axlon control address swaps one of eight 16 KB banks into the middle of the address space. This is the same scheme that the Axlon RAMDISK software, the ADS Integrater and CDY's Omniview and Omnimon RAM-disk versions use.

The 16K/128K switch. The card ships with jumper J1 set to 128 KB. CCP sold a switch kit for $7.95 ($12.95 installed). You could also wire a SPDT on-on switch to J1's three pads (V, C, G). CCP suggested a Radio Shack slide switch hidden behind the first "A" of the ATARI 800 badge beside the cartridge door. Since switching must be done with the power off, the door has to be open to reach it.

The CDY patch. David Young of CDY Consulting recommended an address "patch line" to reduce some software conflicts. CCP provided for it at J2: a wire from J2 pad 1 to the 18th gold finger of the first RAM card, or to pin 1 of a 74LS10 chip on an Atari 16 KB board. Later cards came pre-wired for a "hidden" CDY patch, which needs only a short jumper on the underside of the 800's motherboard between neighbouring RAM-socket pins. CCP warned that a wrongly fitted patch could permanently damage the machine. If you only do one modification, CCP noted that most owners chose the 16K/128K switch.

Using it today

  • Check the jumper. If a game crashes on a RAMCARD-equipped 800, try the 16 KB setting before suspecting the software.
  • Burn-in. CCP's sheet recommended a burn-in run for new boards. For a decades-old card, a long run of a memory tester that understands Axlon banking is the modern equivalent.
  • Software. Use Axlon-aware RAM-disk drivers (such as the Axlon MMS or Omnimon/Omniview RAM disks) or utilities written for the RAMPOWER. Extended memory on an 800 is invisible to software written only for the 130XE's PORTB banking.
  • Modern equivalents. New Axlon-compatible boards, such as 8-Bit Classics' 512K board, 5cfab's 1056 board and the Incognito personality board, give far more memory. A RAMCARD remains a good period-correct choice.

Compatibility

Atari 800 only. It works with all software written for the Axlon RAMPOWER 128. The 256K card also suits software that handles more than eight Axlon banks.

Credits